12-15-2016
You will have to supply a lot more information first.
How did you create the image, and what is the hardware configuration of that machine?
How did you configure the RAID on the new machine, and how did you restore the image?
The error message indicates that the file /stand/boot is either not found, or is corrupted.
This User Gave Thanks to jgt For This Post:
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi friends,
i am getting the following error while booting my system which has SCo UNIX .
=========================
H iinit
PANIC: srmountfun-Error 22
mounting of rootdev hd(1/42)
cannot dump 40863 pages to dempdev hd(1/41) : Space for only 0 pages.
Dump not completed.
safe to power off... (3 Replies)
Discussion started by: sveera
3 Replies
2. SCO
hi, i m a newbie and installed sco unix on my machine. Also i installed win-xp. i tried to modify the boot.ini file but it does not give me a choice in the begining.
please guide me on this. do we get a boot loader for unix like LILO or GRUB?
:confused: (3 Replies)
Discussion started by: 187final
3 Replies
3. SCO
anyone know where I can download or get a boot disk for sco unix v/386? I have an old PC running sco unix v/386 3.2. I dont have an install or boot disk. I need to reset the root password. I have looked all over the internet and cannot find it anywhere. any help would be greatly appreciated.... (5 Replies)
Discussion started by: format
5 Replies
4. SCO
Hi i have a problem after boot with N1 disk and putting N2 disk and pressing the enter in this message:Insert N2(filesystem) floppy and press after by this(pressing enter) the system is reboot!! why??? :confused:
my old pc is a Pentium II 333mhz 3gb hd 64mb ram
please help!! :( (3 Replies)
Discussion started by: panos_pit
3 Replies
5. SCO
Our system is not booting up properly. It keeps going to this screen:
Enter Run Level (0-6, s or S):
I tried to hit all nos# 0-6 is just goes to hung state.
Tried s or S & it brings me to single user mode. I've checked the file systems & found out that all three had 98%. I tried to... (86 Replies)
Discussion started by: jedimaster
86 Replies
6. UNIX for Dummies Questions & Answers
hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless. (11 Replies)
Discussion started by: fredthayer
11 Replies
7. UNIX for Dummies Questions & Answers
UNIX sco release 5.05 system does not boot:cannot open device hd(40)/boot
stage 1 boot failure: error loading hd(40)/bootWhat to do? (2 Replies)
Discussion started by: Joaoalpande
2 Replies
8. SCO
UNIX sco release 5.05 system does not boot:
cannot open device hd(40)/boot
stage 1 boot failure: error loading hd(40)/boot
what to do? (1 Reply)
Discussion started by: Joaoalpande
1 Replies
9. UNIX for Advanced & Expert Users
UNIX sco release 5.05 system does not boot:
cannot open device hd(40)/boot
stage 1 boot failure: error loading hd(40)/boot
what to do? (5 Replies)
Discussion started by: Joaoalpande
5 Replies
10. SCO
HI All,
I have an old SCO-UNIX machine which I support a long standing client / friend with.
I don't use it very often, and is kept switched off. All was well 2 weeks ago, but when I tried to boot today all I get is a continuous set of long beeps but no booting. I have checked inside... (4 Replies)
Discussion started by: andy sleight
4 Replies
LEARN ABOUT OPENSOLARIS
dpt
dpt(7D) Devices dpt(7D)
NAME
dpt - DPT ServeRAID IV SCSI host bus adapter and RAID adapter driver
DESCRIPTION
The dpt driver is a driver for the DPT (Distributed Processing Technology) family of SmartRAID IV SCSI HBA and RAID adapters. The following
HBA adapters are supported: PM2024, PM2044UW, PM2044W, PM2124, PM2124W, PM2144UW, and PM2144W.
The following RAID adapters are supported: PM3224, PM3224W, PM3334UW, and PM3334W.
PRECONFIGURATION
o DPT PM3224 only: Only EPROM 7A and later versions are supported.
o DPT PM2024 and PM2124 only: Only EPROM 6D4 and later versions are supported.
o Use adapters with SmartROM version 3.B or later versions only.
o Be sure that the controller board is installed in a PCI bus-mastering slot.
o Disable PCI parity checking if your firmware version is earlier than version 7A, if your system memory is ECC, or if your system
does not check parity.
Known Problems and Limitations
During system boot, a message may be displayed saying a DPT controller driver cannot be installed. This message indicates that the mother-
board installed in your system may contain ECC memory or may not check parity. If you see this message is displayed, disable PCI parity
checking.
Supported Settings
o I/O Address: Auto
CONFIGURATION
Auto-configuration code determines whether the adapter is present at the configured address and what types of devices are attached to it.
The DPT ServeRAID is primarily used as a disk array (system drive) controller.
To configure the attached disk arrays, you must configure the controller (using the configuration utilities provided by the hardware manu-
facturer) before you boot the Solaris operating environment. You use the configuration utilities to set RAID levels, stripe parameters,
cache mechanisms and perform other functions. For more information, see the user manual supplied with your hardware.
FILES
/kernel/drv/dpt.conf dpt configuration file
/dev/dsk/cndn[s|p]n block device
/dev/rdsk/cndn[s|p]n raw device where:
cn controller n
dn LUN n (0-7)
sn UNIX system slice n (0-15)
pn fdisk(1M) partition(0)
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------------------------------------+
|ATTRIBUTE TYPE ATTRIBUTE VALUE |
|Architecture x86 |
+-----------------------------------------------------------+
SEE ALSO
fdisk(1M), attributes(5), cmdk(7D)
SunOS 5.11 27 November 2000 dpt(7D)