So, I need to do some summing. I have an Apache log file with the following as a typical line:
127.0.0.1 - frank "GET /apache_pb.gif HTTP/1.0" 200 2326
Now, what I'd like to do is a per-minute sum. So, I can have awk tell me the individual minutes, preserving the dates(since this is a... (7 Replies)
Hi
i am new to scripting. i have a file file.dat with content as :
CONTENT_STORAGE PERCENTAGE FLAG:
/storage_01 64% 0
/storage_02 17% 1
I need to update the value of FLAG for a particular CONTENT_STORAGE value
I have written the following code
#!/bin/sh
threshold=20... (1 Reply)
If $1 in file1 matches $2 in file2. Then the value in $2 of file2 is updated to $1"."$2 of file2. The awk seems to only match the two files but not update. Thank you :).
awk
awk 'NR==FNR{A ; next} $1 in A { $2 = a }1' file1 file2
file1
name version
NM_000593 5
NM_001257406... (3 Replies)
I am trying to use awk to match two files that are tab-delimited. When a match is found between file1 $1 and file2 $4, $4 in file2 is updated using the $2 value in file1. If no match is found then the next line is processed. Thank you :).
file1
uc001bwr.3 ADC
uc001bws.3 ADC... (4 Replies)
I am trying to output a tab-delimited result that uses the data from a tab-delimited file to combine and subtract specific lines.
If $4 matches in each line then the first matching sequential $6 value is added to $2, unless the value is 1, then the original $2 is used (like in the case of line... (3 Replies)
In the awk below I am trying to set/update the value of $14 in file2 in
bold, using the matching NM_ in $12 or $9 in file2
with the NM_ in $2 of file1.
The lengths of $9 and $12 can be variable but what is consistent is the start pattern
will always be NM_ and the end pattern is always ;... (2 Replies)
In the perl below, which does execute, I am having trouble with the else in Rule 3. The digit in f{8} is extracted and used to update f accordinly along with the value in f.
There can be either - * or + before the number that is extracted but the same logic applies, that is if the value is greater... (5 Replies)
I have been reading old posts and trying to come up with a solution for the below: Use a tab-delimited input file to assign
point to variables that are used to update a specific field, Rank. I really couldn't find too much in the way of assigning points
to variable, but made an attempt at an awk... (4 Replies)
I have an input file with
A=xyz
B=pqr
I would want the value in Second Field (xyz or pqr) updated with a value present in Shell Variable based on the value passed in the first field. (A or B )
while read line
do
NEW_VALUE = `some functionality done on $line`
If $line=First Field-... (1 Reply)
Hi,
So awk is driving me crazy on this one. I have searched everywhere and read man, docs and every related post Google can find and still no luck. The actual files I need to run this on are sensitive in nature, but it is the same thing as if I needed to calculate weighted grades for multiple... (15 Replies)
Discussion started by: cotilloe
15 Replies
LEARN ABOUT MOJAVE
split
SPLIT(1) BSD General Commands Manual SPLIT(1)NAME
split -- split a file into pieces
SYNOPSIS
split [-a suffix_length] [-b byte_count[k|m]] [-l line_count] [-p pattern] [file [name]]
DESCRIPTION
The split utility reads the given file and breaks it up into files of 1000 lines each. If file is a single dash ('-') or absent, split reads
from the standard input.
The options are as follows:
-a suffix_length
Use suffix_length letters to form the suffix of the file name.
-b byte_count[k|m]
Create smaller files byte_count bytes in length. If ``k'' is appended to the number, the file is split into byte_count kilobyte
pieces. If ``m'' is appended to the number, the file is split into byte_count megabyte pieces.
-l line_count
Create smaller files n lines in length.
-p pattern
The file is split whenever an input line matches pattern, which is interpreted as an extended regular expression. The matching line
will be the first line of the next output file. This option is incompatible with the -b and -l options.
If additional arguments are specified, the first is used as the name of the input file which is to be split. If a second additional argument
is specified, it is used as a prefix for the names of the files into which the file is split. In this case, each file into which the file is
split is named by the prefix followed by a lexically ordered suffix using suffix_length characters in the range ``a-z''. If -a is not speci-
fied, two letters are used as the suffix.
If the name argument is not specified, the file is split into lexically ordered files named with the prefix ``x'' and with suffixes as above.
ENVIRONMENT
The LANG, LC_ALL, LC_CTYPE and LC_COLLATE environment variables affect the execution of split as described in environ(7).
EXIT STATUS
The split utility exits 0 on success, and >0 if an error occurs.
SEE ALSO csplit(1), re_format(7)STANDARDS
The split utility conforms to IEEE Std 1003.1-2001 (``POSIX.1'').
HISTORY
A split command appeared in Version 3 AT&T UNIX.
BUGS
The maximum line length for matching patterns is 65536.
BSD August 21, 2005 BSD