Sponsored Content
Full Discussion: HP C8000 with HP-UX 10.20
Operating Systems HP-UX HP C8000 with HP-UX 10.20 Post 302985167 by vbe on Monday 7th of November 2016 04:46:38 AM
Old 11-07-2016
I would think so as some late K systems had Ultra-2SCSI controllers, but the Ultra320 came out I think with the N4000 andL classes
 

2 More Discussions You Might Find Interesting

1. HP-UX

HP UX 11i and HP C8000

Hey, i want install HP UX 11i on HP C8000. When i start the C8000 i get a prompt. On this Prompt i write BOot P1 P1 is my DVD-ROM (IDE). I get the Message "ERROR: Not a boot path". When i write SEArch the Prompt said: P0 scsiA.6 HP73.4MAT3073NP P1 ide.1 ... (2 Replies)
Discussion started by: numx
2 Replies

2. HP-UX

Help needed HP UX 11.11i new install on C8000 Desktop messaging system error CAN'T FIX

Hi, I have a HP UX C8000 box , have installed 11.11i from 4 x cds numerous times to try to get a functioning Network or to try and get rid of this error on start up, after new install and 1st startup I get an error "The desktop messaging system could not be started" and then advice about... (12 Replies)
Discussion started by: C8000
12 Replies
MPT(4)							   BSD Kernel Interfaces Manual 						    MPT(4)

NAME
mpt -- LSI Fusion-MPT SCSI/Fibre Channel driver SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device scbus device mpt Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): mpt_load="YES" DESCRIPTION
The mpt driver provides support for the LSI Logic Fusion-MPT family of SCSI, Fibre Channel and SAS controllers. HARDWARE
The following controllers are supported by the mpt driver: o LSI Logic 53c1030, LSI Logic LSI2x320-X (Single and Dual Ultra320 SCSI) o LSI Logic AS1064, LSI Logic AS1068 (SAS/SATA) o LSI Logic FC909 (1Gb/s Fibre Channel) o LSI Logic FC909A (Dual 1Gb/s Fibre Channel) o LSI Logic FC919, LSI Logic 7102XP-LC (Single 2Gb/s Fibre Channel) o LSI Logic FC929, LSI Logic FC929X, LSI Logic 7202XP-LC (Dual 2Gb/s Fibre Channel) o LSI Logic FC949X (Dual 4Gb/s Fibre Channel) o LSI Logic FC949E, LSI Logic FC949ES (Dual 4Gb/s Fibre Channel PCI-Express) The Ultra 320 SCSI controller chips supported by the mpt driver can be found onboard on many systems including: o Dell PowerEdge 1750 thru 2850 o IBM eServer xSeries 335 These systems also contain Integrated Raid Mirroring and Integrated Raid Mirroring Enhanced which this driver also supports. The SAS controller chips are also present on many new AMD/Opteron based systems, like the Sun 4100. Note that this controller can drive both SAS and SATA drives or a mix of them at the same time. The Integrated Raid Mirroring available for these controllers is poorly supported at best. The Fibre Channel controller chipset are supported by a broad variety of speeds and systems. The Apple Fibre Channel HBA is in fact the FC949ES card. This driver also supports target mode for Fibre Channel cards. This support may be enabled by setting the desired role of the core via the LSI Logic firmware utility that establishes what roles the card can take on - no separate compilation is required. SEE ALSO
cd(4), ch(4), da(4), pci(4), sa(4), scsi(4), targ(4), mptutil(8), gmultipath(8) LSI Logic Website, http://www.lsilogic.com/. HISTORY
The mpt driver first appeared in FreeBSD 4.6. AUTHORS
The mpt driver was originally written for FreeBSD by Greg Ansley and marginally improved upon by Matt Jacob <mjacob@FreeBSD.org>. Justin Gibbs <gibbs@FreeBSD.org> and Scott Long <scottl@FreeBSD.org> have made more substantial improvements. BUGS
BSD
May 13, 2010 BSD
All times are GMT -4. The time now is 10:58 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy