Sponsored Content
Operating Systems SCO Can not recognize network adapter SCO UNIX in HP z400 Post 302984805 by moein.mojtaba on Tuesday 1st of November 2016 02:32:47 AM
Old 11-01-2016
hi
The nic is Enabled in the CMOS.
NIC is not broken.
How can I find Number pci parameter ؟
tanks .

Last edited by moein.mojtaba; 11-01-2016 at 04:02 AM..
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

SCO Unix and Two Network Cards

Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg Can anyone tell... (1 Reply)
Discussion started by: potter
1 Replies

2. SCO

Sco Unix network issues

I have got a Sco Unix Server, i want to connect some windows workstations. What configurations do i need to make on server and or workstation? (1 Reply)
Discussion started by: tpurazi1
1 Replies

3. AIX

hacmp network adapter re-define

I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies

4. SCO

SCO Unix Network Configuration

Hello Guys, We have an old PC running on SCO Unix V. Is there any sites where i can get manual/procedures on how to install and configure Network. Thanks (2 Replies)
Discussion started by: nrcuevas
2 Replies

5. AIX

change network adapter

hello i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 ) what i need to do after the new adapter installed on the machine? thanks best regards ariec (1 Reply)
Discussion started by: ariec
1 Replies

6. AIX

How to active this network adapter?

When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command: entstat -all ent#|grep -i priority Priority: 5 Active: False How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies

7. UNIX for Dummies Questions & Answers

External Network Adapter for Solaris 10

Hi All, I am new here - this is my first post. I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies

8. UNIX for Dummies Questions & Answers

SCO Unixware 7.1.4 Network Adapter Error

Hi All I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached. I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Discussion started by: flashinwrx
8 Replies

9. SCO

Configuare Network SCO UNIX 5.0.7 on Vmware

hi i installed sco unix open server 5.0.7 on virtual machine vmware and runing it, its work perfect and good. now how i can configuare network at scoadmin that i able to access nework ? ---------- Post updated at 08:56 AM ---------- Previous update was at 01:47 AM ---------- nobody can... (2 Replies)
Discussion started by: farzad226
2 Replies

10. Red Hat

Red Hat 7 cannot recognize ethernet adapter

Hello community, I have a Proliant HP DL380P with the following network adapters: NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter) 82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter) I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
OCF_HEARTBEAT_SENDAR(7) 					OCF resource agents					   OCF_HEARTBEAT_SENDAR(7)

NAME
ocf_heartbeat_SendArp - Broadcasts unsolicited ARP announcements SYNOPSIS
SendArp [start | stop | monitor | meta-data | validate-all] DESCRIPTION
This RA can be used _instead_ of the IPaddr2 or IPaddr RA to send gratuitous ARP for an IP address on a given interface, without adding the address to that interface. For example, if for some resaon you wanted to send gratuitous ARP for addresses managed by IPaddr2 or IPaddr on an additional interface. SUPPORTED PARAMETERS
ip The IP address for sending ARP packet. (required, string, no default) nic The NIC for sending ARP packet. (required, string, no default) background Send ARPs in background. Set to false if you want to test if sending ARPs succeeded. (optional, boolean, default true) SUPPORTED ACTIONS
This resource agent supports the following actions (operations): start Starts the resource. Suggested minimum timeout: 20s. stop Stops the resource. Suggested minimum timeout: 20s. monitor Performs a detailed status check. Suggested minimum timeout: 20. Suggested interval: 10. meta-data Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5. validate-all Performs a validation of the resource configuration. Suggested minimum timeout: 20s. EXAMPLE
The following is an example configuration for a SendArp resource using the crm(8) shell: primitive p_SendArp ocf:heartbeat:SendArp params ip=string nic=string op monitor depth="0" timeout="20" interval="10" SEE ALSO
http://www.linux-ha.org/wiki/SendArp_(resource_agent) AUTHOR
Linux-HA contributors (see the resource agent source for information about individual authors) resource-agents UNKNOWN 06/09/2014 OCF_HEARTBEAT_SENDAR(7)
All times are GMT -4. The time now is 03:21 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy