10-31-2016
What steps did you take after installing all that software?
Some possibilities:
The nic is disabled in the CMOS.
netconfig requires that you input the PCI parameters, and you have left them at the default 0,0,0.
The nic is defective.
This User Gave Thanks to jgt For This Post:
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
Discussion started by: potter
1 Replies
2. SCO
I have got a Sco Unix Server, i want to connect some windows workstations. What configurations do i need to make on server and or workstation? (1 Reply)
Discussion started by: tpurazi1
1 Replies
3. AIX
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies
4. SCO
Hello Guys,
We have an old PC running on SCO Unix V. Is there any sites where i can get manual/procedures on how to install and configure Network. Thanks (2 Replies)
Discussion started by: nrcuevas
2 Replies
5. AIX
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
Discussion started by: ariec
1 Replies
6. AIX
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
7. UNIX for Dummies Questions & Answers
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies
8. UNIX for Dummies Questions & Answers
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Discussion started by: flashinwrx
8 Replies
9. SCO
hi
i installed sco unix open server 5.0.7 on virtual machine vmware and runing it,
its work perfect and good.
now how i can configuare network at scoadmin that i able to access nework ?
---------- Post updated at 08:56 AM ---------- Previous update was at 01:47 AM ----------
nobody can... (2 Replies)
Discussion started by: farzad226
2 Replies
10. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
VALE(4) BSD Kernel Interfaces Manual VALE(4)
NAME
vale -- a very fast Virtual Local Ethernet using the netmap API
SYNOPSIS
device netmap
DESCRIPTION
vale is a feature of the netmap(4) module that implements multiple Virtual switches that can be used to interconnect netmap clients, includ-
ing traffic sources and sinks, packet forwarders, userspace firewalls, and so on.
vale is implemented completely in software, and is extremely fast. On a modern machine it can move almost 20 Million packets per second
(Mpps) per core with small frames, and about 70 Gbit/s with 1500 byte frames.
OPERATION
vale dynamically creates switches and ports as clients connect to it using the netmap(4) API.
vale ports are named vale[bdg:][port] where vale is the prefix indicating a VALE switch rather than a standard interface, bdg indicates a
specific switch (the colon is a separator), and port indicates a port within the switch. Bridge and port names are arbitrary strings, the
only constraint being that the full name must fit within 16 characters.
See netmap(4) for details on the API.
LIMITS
vale currently supports up to 4 switches, 16 ports per switch, with 1024 buffers per port. These hard limits will be changed to sysctl vari-
ables in future releases.
SYSCTL VARIABLES
vale uses the following sysctl variables to control operation:
dev.netmap.bridge The maximum number of packets processed internally in each iteration. Defaults to 1024, use lower values to trade
latency with throughput.
dev.netmap.verbose Set to non-zero values to enable in-kernel diagnostics.
EXAMPLES
Create one switch, with a traffic generator connected to one port, and a netmap-enabled tcpdump instance on another port:
tcpdump -ni vale-a:1 &
pkt-gen -i vale-a:0 -f tx &
Create two switches, each connected to two qemu machines on different ports.
qemu -net nic -net netmap,ifname=vale-1:a ... &
qemu -net nic -net netmap,ifname=vale-1:b ... &
qemu -net nic -net netmap,ifname=vale-2:c ... &
qemu -net nic -net netmap,ifname=vale-2:d ... &
SEE ALSO
netmap(4)
http://info.iet.unipi.it/~luigi/vale/
Luigi Rizzo, Giuseppe Lettieri: VALE, a switched ethernet for virtual machines, June 2012, http://info.iet.unipi.it/~luigi/vale/
AUTHORS
The vale switch was designed and implemented in 2012 by Luigi Rizzo and Giuseppe Lettieri at the Universita` di Pisa.
vale was funded by the European Commission within FP7 Projects CHANGE (257422) and OPENLAB (287581).
BSD
July 27, 2012 BSD