Can not recognize network adapter SCO UNIX in HP z400
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
please Help me .
tanks
Moderator's Comments:
Please use CODE tags, as required by forum rules, when displaying sample input, sample output, and code segments.
Last edited by Don Cragun; 10-30-2016 at 04:57 AM..
Reason: Add CODE and ICODE tags.
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
I have got a Sco Unix Server, i want to connect some windows workstations. What configurations do i need to make on server and or workstation? (1 Reply)
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Hello Guys,
We have an old PC running on SCO Unix V. Is there any sites where i can get manual/procedures on how to install and configure Network. Thanks (2 Replies)
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
hi
i installed sco unix open server 5.0.7 on virtual machine vmware and runing it,
its work perfect and good.
now how i can configuare network at scoadmin that i able to access nework ?
---------- Post updated at 08:56 AM ---------- Previous update was at 01:47 AM ----------
nobody can... (2 Replies)
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
LEARN ABOUT REDHAT
capiinit
capiinit(8) System Manager's Manual capiinit(8)NAME
capiinit - start or stop CAPI-capable ISDN cards
SYNOPSIS
capiinit [OPTIONS] start | stop | show | status | prepare | reload | activate | deactivate
capiinit [OPTIONS] activate|deactivate cardname
capiinit [OPTIONS] activate|deactivate driver [cardname]
DESCRIPTION
capiinit is called with one of the following actions:
start Load all modules and initialize all cards (loading the firmware), which are configured in /etc/capi.conf.
stop Reset all cards and unload modules.
show Show the current configuration.
status Show the current status.
prepare
Load all modules.
activate
Initialize all cards.
activate cardname
Initialize one card (i.e.: c4-ec00).
activate driver [cardnumber]
Initialize one card.
deactivate
Reset all cards.
deactivate cardname
Reset one card (i.e.: c4-ec00).
deactivate driver [cardnumber]
Reset one card.
reload Reset all cards and initialize them again.
Firmware files are searched in this order in the following directories: /usr/share/isdn/`uname -r`, /usr/share/isdn, /usr/lib/isdn,
/lib/isdn.
There is a sample config in /etc/capi.conf.
OPTIONS -c filename, --config filename
Use filename as config file (default is /etc/capi.conf).
-d, --debug
Save patch values for debugging purposes.
-s, --silent
Don't show status information.
AUTHOR
Manpage written from C source by Paul Slootman <paul@debian.org>, updated by Matthias Klose <m@klose.in-berlin.de>.
capiinit(8)