Sponsored Content
Operating Systems Solaris How to Display M4000 XSCF IP from Solaris OS? Post 302984685 by DukeNuke2 on Saturday 29th of October 2016 06:32:41 PM
Old 10-29-2016
Read a little here:

DSCP: Domain to Service Processor Communication Protocol (The Secrets of Olympus)

Not exactly what you need but if your DSCP network is working, you can login to the XSCF via ssh from your Solaris domain and check the settings inside the XSCF (given you have the crendentials to login).

If nothing works and you have a serial line to the XSCF, you can use that to check the settings.

hth,
DN2
 

10 More Discussions You Might Find Interesting

1. Solaris

M4000 graphics card

Hi Guys, Anyone know any commands to verify the graphics card is installed correctly on an M4000? show-displays just comes back and echoes nothing. Also there is on input-device or output-device variable when you run printenv. This in itself is worrying. Any advice would be... (4 Replies)
Discussion started by: callmebob
4 Replies

2. UNIX for Dummies Questions & Answers

Help with restarting SUN m4000 server

I'm trying to power on our SUN m4000 server after a recent shutdown. When I try to connect to the xscf console I'm getting prompted for a password. The system is not asking for a login just a password. Below is the output from the xscf console. Anyone know how I can safely get back to the... (0 Replies)
Discussion started by: orahi001
0 Replies

3. Solaris

fmadm on an M4000

Hi people, Hoping someone has maybe done this before? I'm trying to run fmadm from the xcsf prompt on an M4000 and it won't run, complaining about insufficient privileges, even though the user has supposedly been setup with fieldeng privileges. Anyone got any ideas? Cheers Rgrds... (10 Replies)
Discussion started by: callmebob
10 Replies

4. Solaris

M4000 fault

Hi Guys and Gals, Can someone help me possible? Trying to power up an M4000 and it comes up with xscf fault (reason=0) it then just hangs there. Any help would be gratefully appreciated. Thanks Martin (4 Replies)
Discussion started by: callmebob
4 Replies

5. Solaris

XSCF on M3000

Hi, I've updated a few M3000s to new firmware without any hassle, but on one of them the following is happening: XSCF> getflashimage -u wayner ftp://10.16.122.200/tftpboot/IKXCP1102.tar.gz Error: insufficient free space Any idea how to delete whatever old firmware is on there so I can... (7 Replies)
Discussion started by: cabaiste
7 Replies

6. Solaris

M4000 Server Issue

Dear Team, This time i am facing some problems in Sun SPARC M4000 server. I have a doubt, when we are upgrading the firmware if XSCF , the OBP is also upgraded. What about server OBP, Is that upgardation need to be done separately ? what about DVD-ROM, HARD DISK firmware.... (3 Replies)
Discussion started by: sudhansu
3 Replies

7. Solaris

M4000 Memory Fault

Hi Guys and Gals, Does anyone know how to track down a faulty DIMM on the memory board of an M4000? showhardconf tells me which board it is, but was wondering if there was a way to track it down to a DIMM? Thanks in advance Martin (5 Replies)
Discussion started by: callmebob
5 Replies

8. Solaris

M4000 Mode Switch

Hello, I'm set to go out to our M4000 to reset the XSCF password, since the person who set it up doesn't remember what password they setup. I have all the steps, but the only question I can't find an answer to is around the mode switch. Right now, based on prtdiag, the mode switch is in... (2 Replies)
Discussion started by: QuickNull
2 Replies

9. Solaris

CPU/processor/cores in M4000

Hi Gurus Can someone help me in explaining the below outputs . psrinfo -p 4 /usr/sbin/psrinfo -pv The physical processor has 4 virtual processors (0-3) SPARC64-VI (portid 1024 impl 0x6 ver 0x93 clock 2150 MHz) The physical processor has 4 virtual processors (8-11) SPARC64-VI... (3 Replies)
Discussion started by: ningy
3 Replies

10. IP Networking

M5000 Xscf

I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip. it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out. so my question is, any ideas of what I might... (4 Replies)
Discussion started by: rrodgers
4 Replies
XDG-SETTINGS(1) 						xdg-settings Manual						   XDG-SETTINGS(1)

NAME
xdg-settings - get various settings from the desktop environment SYNOPSIS
xdg-settings {get | check | set} {property} [subproperty] [value] xdg-settings {--help | --list | --manual | --version} DESCRIPTION
xdg-settings gets various settings from the desktop environment. For instance, desktop environments often provide proxy configuration and default web browser settings. Using xdg-settings these parameters can be extracted for use by applications that do not use the desktop environment's libraries (which would use the settings natively). xdg-settings is for use inside a desktop session only. It is not recommended to use xdg-settings as root. OPTIONS
--help Show command synopsis. --list List all properties xdg-settings knows about. --manual Show this manual page. --version Show the xdg-utils version information. PROPERTIES
When using xdg-settings to get, check or set a destkop setting, properties and possibly sub-properties are used to specify the setting to be changed. Some properties (such as default-web-browser) fully describe the setting to be changed. Other properties (such as default-url-scheme-handler) require more information (in this case the actual scheme to set the default handler for) which must be provided in a sub-property. EXIT CODES
An exit code of 0 indicates success while a non-zero exit code indicates failure. The following failure codes can be returned: 1 Error in command line syntax. 2 One of the files passed on the command line did not exist. 3 A required tool could not be found. 4 The action failed. EXAMPLES
Get the desktop file name of the current default web browser xdg-settings get default-web-browser Check whether the default web browser is firefox.desktop, which can be false even if "get default-web-browser" says that is the current value (if only some of the underlying settings actually reflect that value) xdg-settings check default-web-browser firefox.desktop Set the default web browser to google-chrome.desktop xdg-settings set default-web-browser google-chrome.desktop Set the default mailto URL scheme handler to be evolution.desktop xdg-settings set default-url-scheme-handler mailto evolution.desktop AUTHOR
Mike Mammarella Author. COPYRIGHT
Copyright (C) 2009-2011 [FIXME: source] 08/18/2014 XDG-SETTINGS(1)
All times are GMT -4. The time now is 04:49 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy