10-14-2016
Either your D class had the FWSCSI controller option giving you hot swap disks but only 2 disk internal allowed or you had standard on hot swap but could have up to 5 disks in it... Trying to find Ignite-UX to reinstall WILL NOT solve you issue as so far I see no proof Ignite isnt working but as I said above you have a system issue, I have been helping CERN to maintain the running D classes they had so I know what kind of message you get when things go wrong, you dont want to answer what you have been asked, I think its time to close the thread so others dont loose their time too
10 More Discussions You Might Find Interesting
1. HP-UX
can any1 tell me how to make ignite tapes for the HP-ux.
this company said it was: "make_tape_recovery_A", but that don't work. (4 Replies)
Discussion started by: JBX
4 Replies
2. UNIX for Advanced & Expert Users
system:
HP-UX 10.20 with HFS mounted.
How can I convert the HFS to VxFS without an ignite server ?
Is this possible ?
thanks
simon2000 (4 Replies)
Discussion started by: simon2000
4 Replies
3. HP-UX
could any one help me
I have a HP UX 11.0 with a lot of VG and disks connected to SAN. I need to create a Golden Image having only the vg00 of this system. How do i do this using make_sys_image?
In case any have some docs, I would appreciate if You could share it.
Thanks
Dhanish (5 Replies)
Discussion started by: i2admin
5 Replies
4. HP-UX
Sorry if this has been asked and answered, but I can't find this particual problem. I've had an Ignite server running for years on a small internal network with images we load on daily basis. Tried to load two servers, L2000 and C3600 , both with same problem.
# boot lan.192.168.2.2 install
... (0 Replies)
Discussion started by: ddeblance
0 Replies
5. HP-UX
Hello All,
I need to bring down our old 9000 series d350, but my supervisor wants an ignite backup created. I cannot find ignite in the usual places (/opt/ignite) nor can I find it in swlist. As far as I can tell the cd's are long gone.
Is there anywhere else I could look for ignite being... (6 Replies)
Discussion started by: stay0ut
6 Replies
6. HP-UX
Hi
Can I use a vpar as an ignite server? (1 Reply)
Discussion started by: mahlathini
1 Replies
7. AIX
Hi All,
Does AIX has utility like ignite server to make remote os installation using image (2 Replies)
Discussion started by: jayannair
2 Replies
8. HP-UX
I am looking to make bootable tape backups of four machines running HP-UX 09.02, 09.05 and 09.07.
I successfully located Ignite 10.20 and installed it and made a backup on the one machine running HP-UX 10.20. I am having trouble locating information about Ignite for HP-UX 9. Does it exist? Is... (3 Replies)
Discussion started by: whack_job
3 Replies
9. HP-UX
I've read the Ignite User/Admin Guide but I'm having trouble figuring out if I can do a make_net_recovery if the ignite server and client server are on completely different networks? If this can be done is there any special configuration? If I initiate the command from the server it looks like it... (3 Replies)
Discussion started by: gonzotonka
3 Replies
10. HP-UX
Works all.
Depot shared via nfs
dhcp working
setting file system,network,root password,etc
But when i start "go!" with installation,give me
this error.
How to fix,debug?
Thanks
http://s24.postimg.org/5hzbgk551/unixbell3.png (3 Replies)
Discussion started by: Linusolaradm1
3 Replies
iostat(1) General Commands Manual iostat(1)
NAME
iostat - Reports I/O statistics
SYNOPSIS
iostat [drive...] [interval] [count]
OPERANDS
Forces iostat to display specific drives. If drive is not specified (or the specified drive does not exist on the system or cluster,
iostat displays the first two drives (even if more than two disk drives are configured in the system). Causes iostat to report once each
interval seconds. The first report is for all time since the system was last booted, and each subsequent report is for the last interval
only.The value must not be 0. Specifies the number of reports. For example, iostat 1 10 would produce 10 reports at 1-second intervals.
You cannot specify count without interval because the first numeric argument to iostat is assumed to be interval.
DESCRIPTION
The iostat command reports the following information: For terminals (collectively), the number of characters read and written per second.
For each disk, the number of transfers per second and bytes transferred per second (in kilobytes). For the system, the percentage of time
the system has spent in user mode, in user mode running low priority (nice) processes, in system mode, and idling.
To compute this information, iostat counts data transfer completions, the number of words transferred for each disk, and the collective
number of input and output characters for terminals. Also, each sixtieth of a second, iostat examines the state of each disk and makes a
tally if the disk is active.
When you issue an iostat command on a cluster member, it displays statistics only for those disks that are local to the member and that
member's usage of those shared disks that it has mounted. It displays 0 for other disks in the cluster (those it doesn't have mounted),
regardless of whether they are on the shared bus or are local to some other member.
EXAMPLES
The output from this example displays cpu, terminal, and disk statistics for the first two disks on the system providing 5 reports at 1
second intervals:
# iostat 1 5
tty floppy1 dsk9 cpu
tin tout bps tps bps tps us ni sy id
0 3 0 0 0 0 1 0 4 95
4 58 0 0 0 0 1 0 2 97
1 53 0 0 0 0 0 0 2 98
5 59 0 0 0 0 1 0 1 98
6 60 0 0 0 0 1 0 2 97
The second example specifies device names in the command:
# iostat dsk2 dsk3 cdrom2
tty dsk2 cdrom2 dsk3 cpu
tin tout bps tps bps tps bps tps us ni sy id
0 13 11 5 5 2 2427 1213 0 1 1 98
SEE ALSO
Commands:vmstat(1)
iostat(1)