|
|
Sponsored Content
Operating Systems
Linux
Red Hat
Network bonding
Post 302982756 by wviands on Monday 3rd of October 2016 02:06:10 PM
10-03-2016
|
|
10 More Discussions You Might Find Interesting
1. IP Networking
I’m familiar with load balancing.. but Is it possible to actually bond multiple DSL lines together? I hear of ways to bond using MLPPP but that requires support from an ISP. Is there a way to actually bond without support from my ISP, or use say a cable modem and a DSL line together for faster... (0 Replies)
Discussion started by: harley313
0 Replies
2. Red Hat
Hi,
What is IP bonding in Linux.
What are its advantages
How to create a IP bonding in redhat Linux. (1 Reply)
Discussion started by: chetansingh23
1 Replies
3. IP Networking
Hello.
Our Company is spreaded over Germany.
There are main offices an branch offices.
These offices are mostly connecte via multiple sdsl.
We build a IPSEC VPN Infrastructure using Aastaro Security Gateways appliances.
It seemed that only one VPN Connetion between to offices could be... (0 Replies)
Discussion started by: mschwadorf
0 Replies
4. Linux
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
Discussion started by: dr_mabuse
2 Replies
5. Red Hat
I am new to linux. I have a falconstor CDP installation which runs on RHEL 5.5 (Tikanga). There is a vendor option to bond nics in either 802.3ad or round robin, I choose 802.3ad. The server is connected to a Cisco 3750 switch.
The problem is dropped packets and eth03 wont come up in the PO... (0 Replies)
Discussion started by: tjcooper
0 Replies
6. Red Hat
Does anyone know if it's possible to bond two bonds together? My situation is I have two older Cisco switches that cannot carry a LACP (bond level 4) aggregated between them, but separate aggregates can be setup on the switches themselves. In order to have redundancy of two switches I would... (0 Replies)
Discussion started by: christr
0 Replies
7. Red Hat
Hi team,
I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1
to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The
ethernet address is that of the primary interface. I have tried
several different modes,... (3 Replies)
Discussion started by: leo_ultra_leo
3 Replies
8. IP Networking
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Discussion started by: elliottlc
0 Replies
9. Red Hat
I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
Discussion started by: Anjan Ganguly
4 Replies
10. UNIX for Beginners Questions & Answers
bond0 active in eth0 and inactive in eth4. why eth4 received network package?
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: eth0 (primary_reselect failure)
Currently Active Slave: eth0
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
... (4 Replies)
Discussion started by: samran35
4 Replies
LEARN ABOUT SUNOS
systemd-networkd.service
SYSTEMD-NETWORKD.SERVICE(8) systemd-networkd.service SYSTEMD-NETWORKD.SERVICE(8) NAME
systemd-networkd.service, systemd-networkd - Network manager SYNOPSIS
systemd-networkd.service /lib/systemd/systemd-networkd DESCRIPTION
systemd-networkd is a system service that manages networks. It detects and configures network devices as they appear, as well as creating virtual network devices. To configure low-level link settings independently of networks, see systemd.link(5). systemd-networkd will create network devices based on the configuration in systemd.netdev(5) files, respecting the [Match] sections in those files. systemd-networkd will manage network addresses and routes for any link for which it finds a .network file with an appropriate [Match] section, see systemd.network(5). For those links, it will flush existing network addresses and routes when bringing up the device. Any links not matched by one of the .network files will be ignored. It is also possible to explicitly tell systemd-networkd to ignore a link by using Unmanaged=yes option, see systemd.network(5). When systemd-networkd exits, it generally leaves existing network devices and configuration intact. This makes it possible to transition from the initrams and to restart the service without breaking connectivity. This also means that when configuration is updated and systemd-networkd is restarted, netdev interfaces for which configuration was removed will not be dropped, and may need to be cleaned up manually. CONFIGURATION FILES
The configuration files are read from the files located in the system network directory /lib/systemd/network, the volatile runtime network directory /run/systemd/network and the local administration network directory /etc/systemd/network. Networks are configured in .network files, see systemd.network(5), and virtual network devices are configured in .netdev files, see systemd.netdev(5). SEE ALSO
systemd(1), systemd.link(5), systemd.network(5), systemd.netdev(5), systemd-networkd-wait-online.service(8) systemd 237 SYSTEMD-NETWORKD.SERVICE(8)