1. testa
2. testb
3. testc
break here
this is a test
break end here
4. testd
5. test5
6. test6
Thanks in advance.
Regards,
FSPalero
Moderator's Comments:
Repeated refusal to use CODE tags when presenting sample input, sample output, and code segments has resulted in this user being placed in read-only mode for a while.
Continued refusal to properly format posts may result in a permanent ban from this site.
Last edited by Don Cragun; 09-20-2016 at 04:23 AM..
Reason: Add CODE tags again.
Hi All,
I have two comma separated value(CSV) files, say FileA and FileB.
The contents looks like that shown below.
FileA
EmpNo,Name,Age,Sex,
1000,ABC,23,M,
1001,DES,24,F, ... (2 Replies)
Hello I am trying to append an incrimenting number to the end of each line I have it working with a temp file. But I want to do this without a temp file.
a=1
cat "file" | while read LINE
do
echo "$LINE, $a" >> filewithnumbers
a=`expr $a + 1`
... (4 Replies)
Hi
I need to append some text @ end of the first line in a file.
like
myfile.txt
list = a,b,c
list.a=some..
I give the arg "d" . now it append at end of first line
list=a,b,c,d
list.a=some...
Please help me out this (7 Replies)
Hi,
I have gps receiver log..its giving readings .like below
Trying 127.0.0.1...
Connected to localhost.
Escape character is '^]'.
GPSD,R=1
$GPGSV,3,1,11,08,16,328,40,11,36,127,00,28,33,283,39,20,11,165,00*71... (3 Replies)
I have a file "sample.txt" with the content as below:
Hi
This is a Sample Text.
I need a single command using cat which serve the following purpose.
1.display the contents of sample.txt
2.append some text to it
3. and then exit
But, all should be served by a sinle command.:confused: (1 Reply)
Say I have a text file like:
1
3
4
How would I use ksh to put the number '2' into the second line of that file? I'm using OpenBSD so the sed syntax might be a bit different (I have no idea how to use sed, though) (4 Replies)
I would like to add a line to the end of a single column text file. How do I go about doing that?
Input:
BEGIN
1
2
3
Output:
BEGIN
1
2
3
END
Thanks! (1 Reply)
Hi,
I had generated a report in my tool as followsoutput.txt
43.35
9
i needed the script to generate a new file like below
i want to append the text to each of these lines of my filenewoutputfile.txt should be
Total Amount : 43.35
Record Count:9
Regards,
Vasa Saikumar.
... (2 Replies)
In the awk below I am trying to cp and paste each matching line in f2 to $3 in f1 if $2 of f1 is in the line in f2 somewhere. There will always be a match (usually more then 1) and my actual data is much larger (several hundreds of lines) in both f1 and f2. When the line in f2 is pasted to $3 in... (4 Replies)
Discussion started by: cmccabe
4 Replies
LEARN ABOUT DEBIAN
sc_tracediff
SC_TRACEDIFF(1) BSD General Commands Manual SC_TRACEDIFF(1)NAME
sc_tracediff -- display traceroute paths where the path has changed.
SYNOPSIS
sc_tracediff [-a] [-m method] [-n] file1.warts file2.warts
DESCRIPTION
The sc_tracediff utility displays pairs of traceroutes to a destination where the path has changed. It takes two warts files as input and
displays paths where a hop differs by its address. The options are as follows:
-a dump all traceroute pairs regardless of whether they have changed.
-m method
specifies the method used to match pairs of traceroutes together. If dst is specified, traceroutes are matched if the destination IP
address of both traces are the same. If userid is specified, traceroutes are matched if the userid field of both traces are the
same. If dstuserid is specified, traceroutes are matched if the destination IP address and userid fields are the same. By default,
the destination IP address is used.
-n names should be reported instead of IP addresses, where possible.
sc_tracediff can be useful in network monitoring to identify when a forward IP path has changed. In this scenario, it is recommended that
Paris traceroute is used with the same UDP source and destination ports for each execution of scamper so that only paths that have changed
are identified, not merely alternate paths visible due to per-flow load-balancing. By default scamper uses a source port based on the
process ID, which will change with each execution of scamper.
EXAMPLES
The command:
scamper -O warts -o file1.warts -c 'trace -P udp-paris -s 31337' -f list.txt
collects the forward IP paths towards a set of IP addresses found in list.txt using 31337 as the UDP source port value. If the above command
is adjusted to subsequently collect file2.warts, then we can identify paths that have subsequently changed with the command:
sc_tracediff file1.warts file2.warts
If Paris traceroute with ICMP probes is preferred, then the following invocation of scamper is appropriate:
scamper -O warts -o file1.warts -c 'trace -P icmp-paris -d 31337' -f list.txt
In this case, scamper uses 31337 as the ICMP checksum value in each probe.
SEE ALSO scamper(1),
B. Augustin, X. Cuvellier, B. Orgogozo, F. Viger, T. Friedman, M. Latapy, C. Magnien, and R. Teixeira, Avoiding traceroute anomalies with
Paris traceroute, Proc. ACM/SIGCOMM Internet Measurement Conference 2006.
AUTHOR
sc_tracediff is written by Matthew Luckie <mjl@luckie.org.nz>.
BSD April 21, 2011 BSD
09-20-2016
