Sponsored Content
Full Discussion: Solaris install problem
Operating Systems Solaris Solaris install problem Post 302980972 by hicksd8 on Monday 5th of September 2016 05:27:51 PM
Old 09-05-2016
@simplextibi.....where are you getting your media from? Any Solaris media must be the Sparc version. Any OpenBSD must be the Sparc version. Must also be 64-bit version. I believe it also needs to be CD 4.0 minimum. The information you have provided so far is very woolly. Can you please post the boot sequence from totally powered off (no mains connection) status. Then, what 'boot' command are you issuing and to what prompt?

@other subscribers to this thread......it's been a while since I used a V880 but, if we're not logging into the SC at all, how do we know that power to the main box is even on?

Last edited by hicksd8; 09-12-2016 at 05:22 AM..
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Solaris install problem

I am trying to install Solaris 2.8 on an Ultra 5 with Openboot 3.11 from the install cd. I type in boot cdrom, and I get the error: Boot device: /pci@1f,0/pci@1,1/ide@3/cdrom@2,0:f File and args : /platform/sun4u/kernel/genunix. Elf32 read error. I looked up the error, and it said to reset the boot... (2 Replies)
Discussion started by: jeremiebarber
2 Replies

2. Solaris

Install Solaris 10 Problem

Hi! I have tried to install Solaris 10 on my laptop for some time now i have tried a lot of things but i have never been lucky...please can someone of you help me.. I have a Acer Aspire 1350 AMD ATHLON XP-M 2800+ MEMORY: 256MB DDR SDRAM GRAPHICS CARD: VIA KM400 The screen goes black... (1 Reply)
Discussion started by: CreamHarry
1 Replies

3. Solaris

Install problem Solaris 10.1 6/06

Hi all! I'm trying to install Solaris 10.1 6/06 and got a problem under the install,after the first Grub screen the screen went black and all letters are seen as dots, i have installed Solaris 10 earlier and that goes without any problem. Are there any settings i can do to Grub under the first... (2 Replies)
Discussion started by: larsgk
2 Replies

4. Solaris

Solaris install problem!!

I am running an x86 system with a clean 300GB hard drive. i installed solaris10 on it the first time as a slave drive(the other drive had xp on it and it was the active part). it gave me bad file system error among other things...bla bla bla... so i took out the drive with xp on it and switched... (5 Replies)
Discussion started by: vutty81
5 Replies

5. Solaris

Problem after Install SUN solaris x86

after install solaris x86 on my computer success, but it can't boot. When the machine start, and i choose option 1 - default, it shows "W" on screen and system restart . Anyone can help me. My computer : dual core - 1gb ram - x86 (7 Replies)
Discussion started by: quan0509
7 Replies

6. Solaris

Problem of install rsync on Solaris 10

hi all, I have download latest version for rsync from rsync download web site. I trying install rsync tool to sun solaris 10 (SPARC M4000 server) and but get some error. Please see below: -bash-3.00$ ./configure configure.sh: Configuring rsync 3.0.6 checking build system type...... (3 Replies)
Discussion started by: Tlg13team
3 Replies

7. Solaris

Solaris 10 on Enterprise 4500 install problem

Good day, I am dummie on solaris and trying learning about Solaris, so no much experience, this is my problem, I got enterprise 4500 SUN Sparc hardware, has 2 internal SCSI HD, when I try to install Solaris 10 says that "no disk found" at middle of installation, I already change the HD and the... (3 Replies)
Discussion started by: edgargarcia_y2k
3 Replies

8. Solaris

nagios-plugins-1.4.15 Install Problem on Solaris 10

I am trying to install nagios-plugins-1.4.15 on a Solaris 10 box and when I run the ./configure script I get this error: checking for grep that handles long lines and -e... configure: error: no acceptable grep could be found in... (2 Replies)
Discussion started by: thatwaseasy
2 Replies

9. Solaris

Solaris 10 install dvd drive boots, but not recoginized by install process

I am trying to build a Sun Ultra 10 with solaris 10. This computer is one of a collection that was donated to the non-profic company I work for. All media was wiped before I recieved them, so I am starting from stratch. I downloaded the Solaris 10 ISO and burned a DVD. The computer came with a... (4 Replies)
Discussion started by: gwillhight
4 Replies

10. Solaris

No way to install a flar archive of Solaris 10 to Solaris 11.4 zone

I want to migrate a solaris 10 os to solaris 11.4 zone. I did this a)Collect some data like id sysid,disks,ip,etc..on solaris10 OK b)Create this file.cfg with this command on solaris 10 zonep2vchk -c > /migration/sol10.cfg OK c)Create the archive flash on Solaris10 (1 Reply)
Discussion started by: Linusolaradm1
1 Replies
removable-media(9P)					   Kernel Properties for Drivers				       removable-media(9P)

NAME
removable-media - removable media device property DESCRIPTION
A device that supports removable media--such as CDROM, JAZZ, and ZIP drives--and that supports power management and expects automatic mounting of the device via the volume manager should export the boolean (zero length) property removable-media. This property enables the system to make the power state of the device dependent on the power state of the frame buffer and monitor. See the power.conf(4) discussion of the device-dependency-property entry for more information. Devices that behave like removable devices (such as PC ATA cards, where the controller and media both are removed at the same time) should also export this property. EXAMPLES
Example 1: removable-media Entry An example of a removable-media entry from the .conf file of a driver is shown below. # This entry keeps removable media from being powered down unless # the console framebuffer and monitor are powered down # removable-media=1; Example 2: Implementation in attach() Below is an example of how the entry above would be implemented in the attach(9E) function of the driver. xxattach(dev_info_t *dip, ddi_attach_cmd_t cmd) { ... if (ddi_prop_create(DDI_DEV_T_NONE, dip, DDI_PROP_CANSLEEP, "removable-media", NULL, 0)) != DDI_PROP_SUCCESS) goto failed; ... } ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Interface stability |Evolving | +-----------------------------+-----------------------------+ SEE ALSO
power.conf(4), pm(7D), attach(9E), detach(9E), ddi_prop_create(9F) Writing Device Drivers SunOS 5.10 15 Jun 2001 removable-media(9P)
All times are GMT -4. The time now is 05:51 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy