I think that to make any progress here you'll have to access the ALOM (Advanced Lights Out Manager) and login. Then you'll have to start with the following, from the prompt;
Code:
sc> reset -x
Or you can run;
Code:
sc> poweroff
This should take you to the OBP "{ok}" prompt, here you should be able to get some output by running;
Code:
{ok} show-post-results
Post the output - but it does look like a processor card fault.
Regards
Gull04
Last edited by gull04; 09-05-2016 at 10:51 AM..
Reason: Missed prompt
I am trying to install Solaris 2.8 on an Ultra 5 with Openboot 3.11 from the install cd. I type in boot cdrom, and I get the error: Boot device: /pci@1f,0/pci@1,1/ide@3/cdrom@2,0:f File and args : /platform/sun4u/kernel/genunix. Elf32 read error. I looked up the error, and it said to reset the boot... (2 Replies)
Hi!
I have tried to install Solaris 10 on my laptop for some time now i have tried a lot of things but i have never been lucky...please can someone of you help me..
I have a
Acer Aspire 1350
AMD ATHLON XP-M 2800+
MEMORY: 256MB DDR SDRAM
GRAPHICS CARD: VIA KM400
The screen goes black... (1 Reply)
Hi all! I'm trying to install Solaris 10.1 6/06 and got a problem under the install,after the first Grub screen the screen went black and all letters are seen as dots, i have installed Solaris 10 earlier and that goes without any problem.
Are there any settings i can do to Grub under the first... (2 Replies)
I am running an x86 system with a clean 300GB hard drive. i installed solaris10 on it the first time as a slave drive(the other drive had xp on it and it was the active part). it gave me bad file system error among other things...bla bla bla... so i took out the drive with xp on it and switched... (5 Replies)
after install solaris x86 on my computer success, but it can't boot. When the machine start, and i choose option 1 - default, it shows "W" on screen and system restart .
Anyone can help me.
My computer : dual core - 1gb ram - x86 (7 Replies)
hi all,
I have download latest version for rsync from rsync download web site.
I trying install rsync tool to sun solaris 10 (SPARC M4000 server) and but get some error. Please see below:
-bash-3.00$ ./configure
configure.sh: Configuring rsync 3.0.6
checking build system type...... (3 Replies)
Good day,
I am dummie on solaris and trying learning about Solaris, so no much experience, this is my problem, I got enterprise 4500 SUN Sparc hardware, has 2 internal SCSI HD, when I try to install Solaris 10 says that "no disk found" at middle of installation, I already change the HD and the... (3 Replies)
I am trying to install nagios-plugins-1.4.15 on a Solaris 10 box and when I run the ./configure script I get this error:
checking for grep that handles long lines and -e... configure: error: no acceptable grep could be found in... (2 Replies)
I am trying to build a Sun Ultra 10 with solaris 10. This computer is one of a collection that was donated to the non-profic company I work for. All media was wiped before I recieved them, so I am starting from stratch.
I downloaded the Solaris 10 ISO and burned a DVD. The computer came with a... (4 Replies)
I want to migrate a solaris 10 os to solaris 11.4 zone.
I did this
a)Collect some data like id sysid,disks,ip,etc..on solaris10
OK
b)Create this file.cfg with this command on solaris 10
zonep2vchk -c > /migration/sol10.cfg
OK
c)Create the archive flash on Solaris10 (1 Reply)
Discussion started by: Linusolaradm1
1 Replies
LEARN ABOUT OSX
locale::codes::langvar
Locale::Codes::LangVar(3pm) Perl Programmers Reference Guide Locale::Codes::LangVar(3pm)NAME
Locale::Codes::LangVar - standard codes for language variation identification
SYNOPSIS
use Locale::Codes::LangVar;
$lvar = code2langvar('acm'); # $lvar gets 'Mesopotamian Arabic'
$code = langvar2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langvar_codes();
@names = all_langvar_names();
DESCRIPTION
The "Locale::Codes::LangVar" module provides access to standard codes used for identifying language variations, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language variations. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lvar = code2langvar('en','alpha-2');
$lvar = code2langvar('en',LOCALE_CODE_ALPHA_2);
The codesets currently supported are:
alpha
This is the set of alphanumeric codes from the IANA language registry, such as 'arevela' for Eastern Armenian.
This code set is identified with the symbol "LOCALE_LANGVAR_ALPHA".
This is the default code set.
ROUTINES
code2langvar ( CODE [,CODESET] )
langvar2code ( NAME [,CODESET] )
langvar_code2code ( CODE ,CODESET ,CODESET2 )
all_langvar_codes ( [CODESET] )
all_langvar_names ( [CODESET] )
Locale::Codes::LangVar::rename_langvar ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangVar::add_langvar ( CODE ,NAME [,CODESET] )
Locale::Codes::LangVar::delete_langvar ( CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_alias ( NAME ,NEW_NAME )
Locale::Codes::LangVar::delete_langvar_alias ( NAME )
Locale::Codes::LangVar::rename_langvar_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::delete_langvar_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2012 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.16.2 2012-10-11 Locale::Codes::LangVar(3pm)