Also check that
is 1 minute (60000 miliseconds), not 4 or 10 minutes.
Still this can mean that when you stop a service like apache you must wait 1 minute until you can start it again.
I am not by any means a UNIX guru if you can't already tell by the question I'm about to ask.
How do I launch Apache web server on my SOlaris 8 server without rebooting it?
Any help would be much appreciated!!!
-Thanks (5 Replies)
I successfully installed Apache, but When I tried to start it I experienced problems.
After installing and compiling, I typed the PREFIX "usr/local/
apache/bin/apachect1 start." The output was path not found.
After checking the apachect1 file using vi, I found the file empty.
There was no... (4 Replies)
Hi All,
I am trying to start the docbase but i am getting the following error-:
$ ./dm_start_ncsglorbiprd00
interpreter "/bin/sh" not found
file link resolves to "/usr/bin/sh"
sh: ./dm_start_ncsglorbiprd00: not found.
Can anyone please help me in this regard.
Thanks in advance
... (0 Replies)
I've been working on a project to replace one of the my group's primary NIS servers. It also runs mysql and apache, as it is the host for the our team's hardware tracking database and website. Its running apache 1.3, and for some odd reason, I can't get apache to start on system boot. The... (1 Reply)
I just installed Apache 2.2.6 & when trying to start it i got this:
Invalid command 'SSLProtocol', perhaps misspelled or defined by a module not included in the server configuration
Any help? (3 Replies)
Hi,
I just installed Apache 2.0.54 and when I try and start httpd I get
mohit@mohit-desktop:/sw/pkg/apache/bin$ ./httpd -k start
httpd: Could not determine the server's fully qualified domain name, using 127.0.1.1 for ServerName
(13): make_sock: could not bind to address :80
no listening... (1 Reply)
Sir,
I have installed an Apache server in Fedora 9 (packages)
and when i go to etc folder and try the command
httpd -k start
it says command not found....can any one help me out!!!
---------- Post updated at 12:02 PM ---------- Previous update was at 11:46 AM ----------
When i... (4 Replies)
Hello,
I am facing an issue while starting the apache server after compiling php and curl.
Below are the versions i am using.
php-5.2.17
httpd-2.2.17
curl-7.16.0
CentOS5.5x64
Compiling above packages without curl working very fine but when trying to compile php with curl below error is... (1 Reply)
e.g.
File name: File.txt
cat File.txt
Result:
#INBOUND_QUEUE=FAQ1
INBOUND_QUEUE=FAQ2
I want to get the value for one which is not commented out.
Thanks, (3 Replies)
Discussion started by: Tanu
3 Replies
LEARN ABOUT HPUX
ruptime
ruptime(1) General Commands Manual ruptime(1)NAME
ruptime - show status of local machines
SYNOPSIS DESCRIPTION
outputs a status line for each machine on the local network that is running the daemon. status lines are formed from packets broadcast
once every 3 minutes between daemons (see rwhod(1M)) on each host on the network. Each status line has a field for the name of the
machine, the status of the machine (up or down), how long the machine has been up or down, the number of users logged into the machine, and
the 1-, 5- and 15-minute load averages for the machine when the packet was sent.
The status of the machine is reported as ``up'' unless no report has been received from the machine for 11 minutes or more.
The length of time that the machine has been up is shown as:
Load averages are the average number of jobs in the run queue over the last 1-, 5- and 15-minute intervals when the packet was sent.
An example status line output by might be:
The above status line would be interpreted as follows:
is presently ``up'' and has been up for 1 day, 5 hours and 15 minutes. It currently has 7 users logged in. Over the last 1-minute inter-
val, an average of 1.47 jobs were in the run queue. Over the last 5-minute interval, an average of 1.16 jobs were in the run queue. Over
the last 15-minute interval, an average of 0.80 jobs were in the run queue.
If a user has not used the system for an hour or more, the user is considered idle. Idle users are not shown unless the option is speci-
fied.
Options
If no options are specified, the listing is sorted by host name. Options change sorting order as follows:
Sort by load average.
Sort by up time.
Sort by the number of users.
Reverse the sort order.
DIAGNOSTICS
No status report files in
Ask the system administrator to check whether the daemon is running.
AUTHOR
was developed by the University of California, Berkeley.
FILES
Data files
SEE ALSO rwho(1), rwhod(1M).
ruptime(1)