09-05-2016
Hi,
I have the file that you require, PM me and we can sort out a drop - if your operational security will allow you to install a file from an untrusted source.
Regards
Gull04
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
Can X6799A PCI single fiber channel cards be fitted into the top 2 slots of a Sunfire v880. These 2 slots are 66Mhz and X6799A are supposed to be able to connect at this speed.
However , I believe the cards are 5volts , whilst the slots are 3.3volts. (2 Replies)
Discussion started by: markdr011
2 Replies
2. Solaris
We have 3 V880's and we need to purchase a KVM for them. I've never purchased one before. Does anyone have a recommendation for one? (3 Replies)
Discussion started by: dangral
3 Replies
3. Solaris
I have two mechine, one is SUN V880 and another is IBM p570.
I run the same script on V880 and p570 , why the cpu usage always under 50% on V880 but the cpu usage can growth to 100% on p570. (4 Replies)
Discussion started by: golden
4 Replies
4. UNIX for Advanced & Expert Users
Hello,
Need to know all benefits\differences for V890 over V880.
We are really keen to know about this.
Can anybody please take out some time and get us the information.
Regards,
Narinder (4 Replies)
Discussion started by: narinderd
4 Replies
5. Solaris
Hi,
I'mtrying to connect a Device via the serial port to my Solaris 10 environment (Sunfire V880).
I have setup ttyb to connect to the Device. I am getting a connected status in my Port Listing (Using a separate Module that I have in the app running in the environment) but the moment I try to... (0 Replies)
Discussion started by: Alchemist
0 Replies
6. Solaris
Hello All,
I am not a sun expert, but in my network administration job I had to deal with SUN servers. We've to replace a faulty motherboard of SF V880. As per my understanding, host id of machines is programmed in PROM. So will host ID be changed with the replacement of V880 motherboard?... (6 Replies)
Discussion started by: Charagh
6 Replies
7. Solaris
We're trying to install a third T3 array onto our V880. The other two T3's are connected to a qlogic fibre card. We can see this connection fine when we do a luxadm probe -p command. The full device paths are shown etc. ie: the first T3's logical name is c2t1d0 and the second one is c3t1d0.
... (3 Replies)
Discussion started by: mjl927
3 Replies
8. Solaris
Hi everyone, i am totally new to unix i just purchase a sun v880, 16gb ram/8x900 cpu/6 73 gb hd. i want to learn unix/linux i have solaris 10 os instal, i turn on the system it finish check everything and right now i am at {7} ok, what do i do from there. any help would be a blessing from the... (2 Replies)
Discussion started by: Benv880
2 Replies
9. Solaris
Any help on this would be greatly appreciated. I have read other threads on similar subject but still not clear on what this is telling me and what action to take. Do I have a couple of disks that are slowly dying?
While checking disk usage on the V880 I noticed the following:
# format... (3 Replies)
Discussion started by: jamba1
3 Replies
10. Solaris
Hi
I have a 1TB external drive that I want to attach to a SunFire v880 server which runs on Solaris 9. After attaching the external drive what commands should I issue so that the drive will be seen by the server? (7 Replies)
Discussion started by: rahmantanko
7 Replies
LEARN ABOUT SUSE
atmel_fwl
ATMEL_FWL(8) System Manager's Manual ATMEL_FWL(8)
NAME
atmel_fwl - Load firmware into Atmel at76c50x wireless networking chips.
SYNOPSIS
atmel_fwl <interface> /path/to/firmware
DESCRIPTION
atmel_fwl loads firmware images for Atmel at76c50x series wireless networking chips into the Linux driver for same.
Note that this utility is not normally necessary, since the driver will automatically load the correct firmware image via the hotplug sys-
tem. Atmel_fwl is provided for applications where use of the hotplug system may not be desirable.
atmel_fwl should be run after the interface has been created (after card insertion, in the case of PCMCIA cards) but before it is brought
up by running ifconfig.
NOTES
Note that there are two versions of many of the firmware images, the second one with the suffix "-wpa". These are later releases from Atmel
which support WPA privacy. They are only usable by versions of the driver greater than 0.9. Be sure not to use the "-wpa" one unless your
in-kernel driver code is version 0.9 or better. Sadly, as of version 0.9, the in-kernel driver does not actually support the setting of WPA
passphrases.
The firmware images are usually installed in /usr/lib/hotplug/firmware.
The status of the driver, including its firmware loading, is available in /proc/driver/atmel
FILES
/usr/lib/hotplug/firmware
/proc/driver/atmel
SEE ALSO
iwconfig(8), ifconfig(8),
AUTHOR
This manual page was written by Simon Kelley <simon@thekelleys.org.uk>.
ATMEL_FWL(8)