09-05-2016
Hi,
I have the file that you require, PM me and we can sort out a drop - if your operational security will allow you to install a file from an untrusted source.
Regards
Gull04
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
Can X6799A PCI single fiber channel cards be fitted into the top 2 slots of a Sunfire v880. These 2 slots are 66Mhz and X6799A are supposed to be able to connect at this speed.
However , I believe the cards are 5volts , whilst the slots are 3.3volts. (2 Replies)
Discussion started by: markdr011
2 Replies
2. Solaris
We have 3 V880's and we need to purchase a KVM for them. I've never purchased one before. Does anyone have a recommendation for one? (3 Replies)
Discussion started by: dangral
3 Replies
3. Solaris
I have two mechine, one is SUN V880 and another is IBM p570.
I run the same script on V880 and p570 , why the cpu usage always under 50% on V880 but the cpu usage can growth to 100% on p570. (4 Replies)
Discussion started by: golden
4 Replies
4. UNIX for Advanced & Expert Users
Hello,
Need to know all benefits\differences for V890 over V880.
We are really keen to know about this.
Can anybody please take out some time and get us the information.
Regards,
Narinder (4 Replies)
Discussion started by: narinderd
4 Replies
5. Solaris
Hi,
I'mtrying to connect a Device via the serial port to my Solaris 10 environment (Sunfire V880).
I have setup ttyb to connect to the Device. I am getting a connected status in my Port Listing (Using a separate Module that I have in the app running in the environment) but the moment I try to... (0 Replies)
Discussion started by: Alchemist
0 Replies
6. Solaris
Hello All,
I am not a sun expert, but in my network administration job I had to deal with SUN servers. We've to replace a faulty motherboard of SF V880. As per my understanding, host id of machines is programmed in PROM. So will host ID be changed with the replacement of V880 motherboard?... (6 Replies)
Discussion started by: Charagh
6 Replies
7. Solaris
We're trying to install a third T3 array onto our V880. The other two T3's are connected to a qlogic fibre card. We can see this connection fine when we do a luxadm probe -p command. The full device paths are shown etc. ie: the first T3's logical name is c2t1d0 and the second one is c3t1d0.
... (3 Replies)
Discussion started by: mjl927
3 Replies
8. Solaris
Hi everyone, i am totally new to unix i just purchase a sun v880, 16gb ram/8x900 cpu/6 73 gb hd. i want to learn unix/linux i have solaris 10 os instal, i turn on the system it finish check everything and right now i am at {7} ok, what do i do from there. any help would be a blessing from the... (2 Replies)
Discussion started by: Benv880
2 Replies
9. Solaris
Any help on this would be greatly appreciated. I have read other threads on similar subject but still not clear on what this is telling me and what action to take. Do I have a couple of disks that are slowly dying?
While checking disk usage on the V880 I noticed the following:
# format... (3 Replies)
Discussion started by: jamba1
3 Replies
10. Solaris
Hi
I have a 1TB external drive that I want to attach to a SunFire v880 server which runs on Solaris 9. After attaching the external drive what commands should I issue so that the drive will be seen by the server? (7 Replies)
Discussion started by: rahmantanko
7 Replies
LEARN ABOUT DEBIAN
slugimage
SLUGIMAGE(1) General Commands Manual SLUGIMAGE(1)
NAME
slugimage - Manipulate NSLU2 firmware images
SYNOPSIS
slugimage [-p|-u] [options]
DESCRIPTION
slugimage can be used to create or unpack NSLU2 firmware images.
OPTIONS
-d, --debug
Turn on debugging output
-q, --quiet
Turn off status messages
-u, --unpack
Unpack a firmware image
-p, --pack
Pack a firmware image
-l, --little
Convert Kernel and Ramdisk to little-endian
-i, --input
Input firmware image filename
-o, --output
Output firmware image filename
-b, --redboot
Input/Output RedBoot filename
-k, --kernel
Input/Ouptut Kernel filename
-s, --sysconf
Input/Output SysConf filename
-r, --ramdisk
Input/Output Ramdisk filename(s)
-f, --fisdir
Input/Output FIS directory filename
-y, --payload
Input/Output Payload filename
-t, --trailer
Input/Output Trailer filename
-e, --ethaddr
Set the Ethernet address
AUTHOR
This man page was written by Joey Hess, <joey@kitenet.net>.
SLUGIMAGE(1)