09-05-2016
Hi,
Can you be a bit more specific about the problem with the disk?
Regards
Gull04
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
Can X6799A PCI single fiber channel cards be fitted into the top 2 slots of a Sunfire v880. These 2 slots are 66Mhz and X6799A are supposed to be able to connect at this speed.
However , I believe the cards are 5volts , whilst the slots are 3.3volts. (2 Replies)
Discussion started by: markdr011
2 Replies
2. Solaris
We have 3 V880's and we need to purchase a KVM for them. I've never purchased one before. Does anyone have a recommendation for one? (3 Replies)
Discussion started by: dangral
3 Replies
3. Solaris
I have two mechine, one is SUN V880 and another is IBM p570.
I run the same script on V880 and p570 , why the cpu usage always under 50% on V880 but the cpu usage can growth to 100% on p570. (4 Replies)
Discussion started by: golden
4 Replies
4. UNIX for Advanced & Expert Users
Hello,
Need to know all benefits\differences for V890 over V880.
We are really keen to know about this.
Can anybody please take out some time and get us the information.
Regards,
Narinder (4 Replies)
Discussion started by: narinderd
4 Replies
5. Solaris
Hi,
I'mtrying to connect a Device via the serial port to my Solaris 10 environment (Sunfire V880).
I have setup ttyb to connect to the Device. I am getting a connected status in my Port Listing (Using a separate Module that I have in the app running in the environment) but the moment I try to... (0 Replies)
Discussion started by: Alchemist
0 Replies
6. Solaris
Hello All,
I am not a sun expert, but in my network administration job I had to deal with SUN servers. We've to replace a faulty motherboard of SF V880. As per my understanding, host id of machines is programmed in PROM. So will host ID be changed with the replacement of V880 motherboard?... (6 Replies)
Discussion started by: Charagh
6 Replies
7. Solaris
We're trying to install a third T3 array onto our V880. The other two T3's are connected to a qlogic fibre card. We can see this connection fine when we do a luxadm probe -p command. The full device paths are shown etc. ie: the first T3's logical name is c2t1d0 and the second one is c3t1d0.
... (3 Replies)
Discussion started by: mjl927
3 Replies
8. Solaris
Hi everyone, i am totally new to unix i just purchase a sun v880, 16gb ram/8x900 cpu/6 73 gb hd. i want to learn unix/linux i have solaris 10 os instal, i turn on the system it finish check everything and right now i am at {7} ok, what do i do from there. any help would be a blessing from the... (2 Replies)
Discussion started by: Benv880
2 Replies
9. Solaris
Any help on this would be greatly appreciated. I have read other threads on similar subject but still not clear on what this is telling me and what action to take. Do I have a couple of disks that are slowly dying?
While checking disk usage on the V880 I noticed the following:
# format... (3 Replies)
Discussion started by: jamba1
3 Replies
10. Solaris
Hi
I have a 1TB external drive that I want to attach to a SunFire v880 server which runs on Solaris 9. After attaching the external drive what commands should I issue so that the drive will be seen by the server? (7 Replies)
Discussion started by: rahmantanko
7 Replies
hdio(7I) Ioctl Requests hdio(7I)
NAME
hdio - SMD and IPI disk control operations
SYNOPSIS
#include <sys/hdio.h>
DESCRIPTION
Note - The SMC and IPI drivers have been discontinued. dkio(7I) is now the preferred method for retrieving disk information.
The SMD and IPI disk drivers supplied with this release support a set of ioctl(2) requests for diagnostics and bad sector information.
Basic to these ioctl() requests are the definitions in <sys/hdio.h>.
IOCTLS
HDKIOCGTYPE The argument is a pointer to a hdk_type structure (described below). This ioctl() gets specific information from the hard
disk.
HDKIOCSTYPE The argument is a pointer to a hdk_type structure (described below). This ioctl() sets specific information about the hard
disk.
/*
* Used for drive info
*/
struct hdk_type {
ushort_t hdkt_hsect; /* hard sector count (read only) */
ushort_t hdkt_promrev; /* prom revision (read only) */
uchar_t hdkt_drtype; /* drive type (ctlr specific) */
uchar_t hdkt_drstat; /* drive status (ctlr specific, ro) */
};
HDKIOCGBAD The argument is a pointer to a hdk_badmap structure (described below). This ioctl() is used to get the bad sector map from
the disk.
HDKIOCSBAD The argument is a pointer to a hdk_badmap structure (described below). This ioctl() is used to set the bad sector map on
the disk.
/*
* Used for bad sector map
*/
struct hdk_badmap {
caddr_t hdkb_bufaddr; /* address of user's map buffer */
};
HDKIOCGDIAG The argument is a pointer to a hdk_diag structure (described below). This ioctl() gets the most recent command that failed
along with the sector and error number from the hard disk.
/*
* Used for disk diagnostics
*/
struct hdk_diag {
ushort_t hdkd_errcmd; /* most recent command in error */
daddr_t hdkd_errsect; /* most recent sector in error */
uchar_t hdkd_errno; /* most recent error number */
uchar_t hdkd_severe; /* severity of most recent error */
};
SEE ALSO
ioctl(2), dkio(7I)
SunOS 5.10 13 Aug 2002 hdio(7I)