Sponsored Content
Full Discussion: Sunfire V880
Special Forums Hardware Sunfire V880 Post 302980913 by simplextibi on Monday 5th of September 2016 03:17:35 AM
Old 09-05-2016
Sunfire V880

Hi
Does someone have the latest firmware for a sunfire v880
I have a problem with the FC-AL disk i guess i need to upgrade the firmware but i dont have a support with oracle and i can't find it anywhere

thank you
 

10 More Discussions You Might Find Interesting

1. Solaris

X6799A PCI cards and Sunfire v880

Hi, Can X6799A PCI single fiber channel cards be fitted into the top 2 slots of a Sunfire v880. These 2 slots are 66Mhz and X6799A are supposed to be able to connect at this speed. However , I believe the cards are 5volts , whilst the slots are 3.3volts. (2 Replies)
Discussion started by: markdr011
2 Replies

2. Solaris

KVM for V880's

We have 3 V880's and we need to purchase a KVM for them. I've never purchased one before. Does anyone have a recommendation for one? (3 Replies)
Discussion started by: dangral
3 Replies

3. Solaris

Sun V880

I have two mechine, one is SUN V880 and another is IBM p570. I run the same script on V880 and p570 , why the cpu usage always under 50% on V880 but the cpu usage can growth to 100% on p570. (4 Replies)
Discussion started by: golden
4 Replies

4. UNIX for Advanced & Expert Users

V890 Benefits over V880

Hello, Need to know all benefits\differences for V890 over V880. We are really keen to know about this. Can anybody please take out some time and get us the information. Regards, Narinder (4 Replies)
Discussion started by: narinderd
4 Replies

5. Solaris

Serial Port Connection to a Sunfire V880 (having Solaris 10)

Hi, I'mtrying to connect a Device via the serial port to my Solaris 10 environment (Sunfire V880). I have setup ttyb to connect to the Device. I am getting a connected status in my Port Listing (Using a separate Module that I have in the app running in the environment) but the moment I try to... (0 Replies)
Discussion started by: Alchemist
0 Replies

6. Solaris

Host ID of v880

Hello All, I am not a sun expert, but in my network administration job I had to deal with SUN servers. We've to replace a faulty motherboard of SF V880. As per my understanding, host id of machines is programmed in PROM. So will host ID be changed with the replacement of V880 motherboard?... (6 Replies)
Discussion started by: Charagh
6 Replies

7. Solaris

V880 and T3 array issue

We're trying to install a third T3 array onto our V880. The other two T3's are connected to a qlogic fibre card. We can see this connection fine when we do a luxadm probe -p command. The full device paths are shown etc. ie: the first T3's logical name is c2t1d0 and the second one is c3t1d0. ... (3 Replies)
Discussion started by: mjl927
3 Replies

8. Solaris

install solaris on v880

Hi everyone, i am totally new to unix i just purchase a sun v880, 16gb ram/8x900 cpu/6 73 gb hd. i want to learn unix/linux i have solaris 10 os instal, i turn on the system it finish check everything and right now i am at {7} ok, what do i do from there. any help would be a blessing from the... (2 Replies)
Discussion started by: Benv880
2 Replies

9. Solaris

Sunfire V880 Internal Disk Problem

Any help on this would be greatly appreciated. I have read other threads on similar subject but still not clear on what this is telling me and what action to take. Do I have a couple of disks that are slowly dying? While checking disk usage on the V880 I noticed the following: # format... (3 Replies)
Discussion started by: jamba1
3 Replies

10. Solaris

Attaching 1TB external drive to SunFire v880

Hi I have a 1TB external drive that I want to attach to a SunFire v880 server which runs on Solaris 9. After attaching the external drive what commands should I issue so that the drive will be seen by the server? (7 Replies)
Discussion started by: rahmantanko
7 Replies
qthid(1)							      OZ9AEC								  qthid(1)

NAME
qthid - simple controller for the Funcube Dongle SDR SYNOPSIS
qthid DESCRIPTION
This program is a Graphical User Interface to control a radio receiver called the Funcube Dongle SDR. This program was written mainly by Alexandru Csete, OZ9AEC based upon initial code from Howard Long, G6LVB. For more information on the FUNcube project please visit http://www.funcube.org.uk/ and the latest on the FUNcube SDR dongle visit http://www.funcubedongle.com/ It provides full support for the Funcube Dongle API:: * Change frequency and apply frequency correction. * Change RF gains and filters. * Change IF gains and filters. * LNA enhancement, bias current, etc. * I/Q correction. * Auto-repeat tuning buttons (click and hold button to scan). * Variable frequency step. * Upgrade and verify the firmware. The qthid program implements the full API available with firmware versions 18f or greater. It should cover all the functionality provided by the "fully functional windows frontend". Note that the majority of this full API is only available since firmware 18f and qthid 3.0 will not work with earlier firmware. The application will simply fail to detect any FCD with earlier firmwares. You can use qthid-2.2 to upgrade your firmware to 18f or later. SEE ALSO
qthid-2.2(1), gnuradio(1), gqrx(1) AUTHOR
This manual page was written by Maitland Bottoms for the Debian project (but may be used by others). COPYRIGHT
Copyright (c) 2012 A. Maitland Bottoms <bottoms@debian.org> This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MER- CHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. QTHID
3.1 qthid(1)
All times are GMT -4. The time now is 06:55 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy