09-02-2016
IBM Power Linux Cluster Fence device on Power8 Platform
wasn't quite sure which forum to post in.
What typical fence device to configure for a Power Linux PaceMaker Cluster running on the Power8 Platform (S822 Model of hardware), or what should be ordered with the S822 for use as a Fence Device?
6 More Discussions You Might Find Interesting
1. Solaris
Hi All ,
I would like to know the procedure for increasing shared volume space in sun cluster .
Currently the configuration is like these .
Main stripe
oradb1/d91 2 1 /dev/did/rdsk/d35s0 1 /dev/did/rdsk/d36s0 =Total 49 Gb
oradb1/d94 -p oradb1/d91 -o 88080480 -b 14680064 ==Total 7 GB... (4 Replies)
Discussion started by: sahil_shine
4 Replies
2. AIX
Hello,
I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization.
So when booted , it goes into OPEN Firmware
I/O Hosting requires a hosting partition boot not permitted exit called
> ok
Panel shows > IO... (3 Replies)
Discussion started by: filosophizer
3 Replies
3. AIX
Hello,
Got a IBM Power8 box (S822) that I am configuring for replacement of our existing IBM machine.
Wanted to touch base with the expert community here to ensure I don't miss anything critical in my setup/config of AIX.
Did a fresh AIX 7.1 install on the internal scsi hdisk, mirror'ed... (3 Replies)
Discussion started by: c3rb3rus
3 Replies
4. Red Hat
I have 2 VM's setup with a shared VMware disk running RHEL 7.1 (just updated to 7.2 with yum update), and would like to know what is the easiest Fence device to implement for testing purposes. Apparently, I need a fence device before my IP resources will come online.
I have the cluster... (1 Reply)
Discussion started by: mrmurdock
1 Replies
5. Solaris
I build up two node cluster (node1, node2) in virtualbox. For these two nodes I add 5 shared disk. (Also each node have own OS disk).
1 shared disk for vtoc
2 shared disk for NFS resource group
2 shared disk for WEB resource group
When I finished my work; two nodes was ok and shared disk... (4 Replies)
Discussion started by: sonofsunra
4 Replies
6. AIX
A team member installed the wrong version of License Code on a Power 740 system used in our Development environment.
The system will no longer boot.
Does anyone have IBM documentation or experience to share on recovering a system that currently reports "Unsupported License Code version... (1 Reply)
Discussion started by: kevinedailey
1 Replies
LEARN ABOUT OPENSOLARIS
clprivnet
clprivnet(7) Sun Cluster Device and Network Interfaces clprivnet(7)
NAME
clprivnet - SUNW,clprivnet Sun Cluster private network driver
SYNOPSIS
/dev/clprivnet
DESCRIPTION
Note -
Beginning with the Sun Cluster 3.2 release, Sun Cluster software includes an object-oriented command set. Although Sun Cluster software
still supports the original command set, Sun Cluster procedural documentation uses only the object-oriented command set. For more infor-
mation about the object-oriented command set, see the Intro(1CL) man page.
The SUNW,clprivnet Sun Cluster private network driver is a STREAMS pseudo driver supporting Sun Cluster resident applications that use
standard Solaris interfaces to communicate over the Sun Cluster private network. By striping data traffic over all links, this driver opti-
mally utilizes the bandwidth of the private network while supporting highly available, software fault-tolerant communication.
APPLICATION PROGRAMMING INTERFACE
The driver is supported by the character-special device /dev/clprivnet, but is reserved for Sun Cluster internal operation and the standard
Solaris network utilities. This interface must not be directly used for general application communication.
ADMINISTRATION
The administration and configuration of the driver as a network interface is done completely by the Sun Cluster infrastructure internals.
FILES
/dev/clprivnet
clprivnet special character device
/usr/kernel/drv/clprivnet.conf
System-wide default device driver properties
Sun Cluster 3.2 05 Sep 2007 clprivnet(7)