I’m familiar with load balancing.. but Is it possible to actually bond multiple DSL lines together? I hear of ways to bond using MLPPP but that requires support from an ISP. Is there a way to actually bond without support from my ISP, or use say a cable modem and a DSL line together for faster... (0 Replies)
Hello.
Our Company is spreaded over Germany.
There are main offices an branch offices.
These offices are mostly connecte via multiple sdsl.
We build a IPSEC VPN Infrastructure using Aastaro Security Gateways appliances.
It seemed that only one VPN Connetion between to offices could be... (0 Replies)
I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0.
Here's what I did:
created file /etc/modprobe.d/bonding.d and added the following to it:
alias bond0 bonding
options bonding... (2 Replies)
I am new to linux. I have a falconstor CDP installation which runs on RHEL 5.5 (Tikanga). There is a vendor option to bond nics in either 802.3ad or round robin, I choose 802.3ad. The server is connected to a Cisco 3750 switch.
The problem is dropped packets and eth03 wont come up in the PO... (0 Replies)
Does anyone know if it's possible to bond two bonds together? My situation is I have two older Cisco switches that cannot carry a LACP (bond level 4) aggregated between them, but separate aggregates can be setup on the switches themselves. In order to have redundancy of two switches I would... (0 Replies)
Hi team,
I'm running into a problem configuring bonding on an CentOS 64bit on DELL Server. I'm connecting eth0 and eth1
to a Cisco 2948 (CatOS 8.1(3)) and receiving flapping notices. The
ethernet address is that of the primary interface. I have tried
several different modes,... (3 Replies)
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
I have one production system where my customized application runs.The applications require seamless network connectivity with different machines connected in LAN and WAN. As these applications are very critical, it is very much required to have a seamless network activity.The applications are... (4 Replies)
bond0 active in eth0 and inactive in eth4. why eth4 received network package?
Bonding Mode: fault-tolerance (active-backup)
Primary Slave: eth0 (primary_reselect failure)
Currently Active Slave: eth0
MII Status: up
MII Polling Interval (ms): 100
Up Delay (ms): 0
Down Delay (ms): 0
... (4 Replies)
Discussion started by: samran35
4 Replies
LEARN ABOUT REDHAT
usernetctl
USERNETCTL(8) System Manager's Manual USERNETCTL(8)NAME
usernetctl - allow a user to manipulate a network interface if permitted
SYNOPSIS
usernetctl interface-name up|down|report
DESCRIPTION
usernetctl checks to see if users are allowed to manipulate the network interface specified by interface-name, and then tries to bring the
network interface up or down, if up or down was specified on the command line, or returns true or false status (respectively) if the report
option was specified.
usernetctl is not really meant to be called directly by users, though it currently works fine that way. It is used as a wrapper by the
ifup and ifdown scripts, so that users can do exactly the same thing as root:
ifup interface-name
ifdown interface-name
and ifup and ifdown will call usernetctl automatically to allow the interface status change.
OPTIONS
interface-name
The name of the network interface to check; for example, "ppp0". For backwards compatibility, "ifcfg-ppp0" and "/etc/sysconfig/net-
work-scripts/ifcfg-ppp0" are also supported.
up|down
Attempt to bring the interface up or down.
report Report on whether users can bring the interface up or down.
NOTES
Alternate device configurations may inherit the default configuration's permissions.
RHS Red Hat, Inc. USERNETCTL(8)