Sponsored Content
Top Forums UNIX for Advanced & Expert Users RedHat eth interfaces not seem to be present Post 302976708 by zaxxon on Monday 4th of July 2016 06:54:34 AM
Old 07-04-2016
Thanks for sharing Smilie
 

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Eth err: "3c501 device eth0 does not seem to be present"

HI, When I do 'service network restart' , I am getting the following error. "3c501 device eth0 does not seem to be present, delaying initialization" Can any one suggest me the cause/solution for this? When I do 'lspci' it is showing the ehternet card as " Ethernet controller"Marvell... (2 Replies)
Discussion started by: praveen_b744
2 Replies

2. Linux

Renaming eth interfaces

Hi I had a DL380 with two two port eth cards. I now replaced one with a four port eth card and my interfaces seemed to have jumped around. Is there a method of moving eth ports... eg making port eth4 eth2.:confused: (2 Replies)
Discussion started by: theroncj
2 Replies

3. UNIX for Dummies Questions & Answers

NIC and eth connection

folks; This might sounds stupid but i hope someone can give me an answer: On my Linux SUSE boxes, i have 2 NIC cards NIC1 & NIC2. I always assumed that NIC1 is eth0 when i run "ifconfig" and NIC2 is eth1 but i noticed that's not always the case. Is there a way or a command i can run to find... (1 Reply)
Discussion started by: Katkota
1 Replies

4. IP Networking

Eth interfaces UP but NOT RUNNING

Hi people, I have a solaris OS system. I configured its interfaces. They are UP but not in RUNNING status except loopback interface. I made the interfaces DOWN and UP again. The other side of the interfaces (switch ports) are UP. Does anyone have any idea? What may cause this problem, How can I... (1 Reply)
Discussion started by: hubatuwang
1 Replies

5. Red Hat

Present LUN in Redhat

Hi, I created a new vdisk and presented it to a BL460c class server. The LUN was successfully created and presented. My problem however is that I am unable to see the newly added LUN on my OS? I have rebooted the box but no joy. Just wondering if you have any ideas on how this can be... (5 Replies)
Discussion started by: Duffs22
5 Replies

6. Solaris

Interfaces and Virtual-interfaces queries

Hi Al, In course of understanding networking in Solaris, I have these doubts on Interfaces. Please clarify me. I have done fair research in this site and others but could not be clarified. 1. In the "ifconfig -a" command, I see many interfaces and their configurations. But I see many... (1 Reply)
Discussion started by: satish51392111
1 Replies

7. Shell Programming and Scripting

dhcpclient for all the eth* which has no ip

I want to run dhcpclient for all the eth* which has no ip for example eth0 Link encap:Ethernet HWaddr 00:1E:67:3E:BA:EF UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0... (6 Replies)
Discussion started by: yanglei_fage
6 Replies

8. UNIX for Dummies Questions & Answers

Traffic moves to another eth

hi guys I have a server which has 2 nics eth0 and eth1 eth0 is used for our email traffic server. everything working fine some time later a eth1 was added for backup purposes so this new nic sends data to another vlan for backup purposes all of a sudden our mail server starts to fail... (3 Replies)
Discussion started by: karlochacon
3 Replies

9. Red Hat

ifconfig eth - errors after certain packets received

Hi, I am facing an issue with one of the 10G fiber link. After certain packets received. I am seeing errors in ifconfig eth* output. MTU is set to 9000. any idea? (1 Reply)
Discussion started by: snchaudhari2
1 Replies
RHN_REGISTER(8) 						   Red Hat, Inc.						   RHN_REGISTER(8)

NAME
rhn_register - Connect to Spacewalk Server, Red Hat Satellite or Red Hat Network Classic. SYNOPSIS
rhn_register [options] DESCRIPTION
rhn_register is a client program that registers your system with "Spacewalk Server", "Red Hat Satellite" or "Red Hat Network Classic". After registering, your system can receive software updates, install new software, and remotely manage your system. It can run both in graphical and text modes. OPTIONS
-v, --verbose Increase the debugging output. --proxy=PROXY Specify an http proxy to use. --proxyUser=PROXYUSER Specify a username to use for an authenticated proxy. This option must be used in conjunction with proxyPassword. --proxyPassword=PROXYPASSWORD Specify a password to use for an authenticated proxy. This option must be used in conjunction with proxyUser. --nox Run in text mode. --version Show the program's version number and exit. -h, --help Show a help message and exit. FILES
/etc/sysconfig/rhn/systemid The digital server ID for this machine if the system has been registered onto "Spacewalk Server" or "Red Hat Satellite" or "Red Hat Network Classic". This file does not exist otherwise. /etc/sysconfig/rhn/up2date The common configuration file used by Red Hat client programs. SEE ALSO
rhn_check(8), rhnreg_ks(8), rhnsd(8), rhn-profile-sync(8), rhnplugin(8), up2date(5). AUTHORS
See the AUTHORS file included with this software. This manual page was written by James Bowes <jbowes@redhat.com> BUGS
Report bugs to <http://bugzilla.redhat.com>. COPYRIGHT
Copyright (C) 1999-2011 Red Hat, Inc. This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICU- LAR PURPOSE. Linux 2011 February 4 RHN_REGISTER(8)
All times are GMT -4. The time now is 05:57 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy