|
|
Sponsored Content
Special Forums
UNIX and Linux Applications
Infrastructure Monitoring
Problem with service monitoring
Post 302976314 by anaigini45 on Monday 27th of June 2016 11:23:13 PM
06-28-2016
|
|
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi all,
I am looking for api to get me system monitoring statictics every 5 minutes.
I am looking at the following statistics:
1. System CPU Usage
2. Process CPU Usage
3. Process Memory Usage
4. I/O Usage for a certain disk.
5. Process I/O bytes/sec utilization.
I have seen very... (2 Replies)
Discussion started by: uiqbal
2 Replies
2. AIX
Dear All,
When i am start the service netd i am facing the problem
0513-015 The inetd Subsystem could not be started
Please check subsystem resources and try again later.
please suggest me.
It is urgent (1 Reply)
Discussion started by: pernasivam
1 Replies
3. Linux
Hi guys,
please help me out my smartd service is not being up.
$ sudo /sbin/service smartd restart
Shutting down smartd:
Starting smartd:
$
Take a look of /etc/smartd.conf
/dev/sda -H -m... (1 Reply)
Discussion started by: daya.pandit
1 Replies
4. Solaris
hi all,
i am trying to enable pool service
but i recive this message
-bash-3.00# pooladm
pooladm: couldn't open pools state file: Facility is not active
-bash-3.00# pooladm -e
svcadm: Instance "svc:/system/pools:default" is in maintenance state.
pooladm: cannot enable pools:... (4 Replies)
Discussion started by: corvinusbsd
4 Replies
5. Shell Programming and Scripting
Hi,
I am new to shell programming,
I would like to write a script which will monitor sendmail service in linux, and if service goes down it will send the mail
can you please suggest me how to monitor the service?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
6. Linux
hello,
i'm having some performance problem on one of my linux machines and i hope someone will be able to help me analyzing the problem.
machine info:
Linux fedora, cpu x 4 cores of 1.6Ghz, 8G memory, 8G swap.
i've enabled sar on my machine and created a graph using ksar utility for... (15 Replies)
Discussion started by: levic
15 Replies
7. Shell Programming and Scripting
Hi All,
I am creating df monitoring script. but facing some below problm.
Please see the below code.
df_threshold=90;
for i in `cat df_fnl.txt`
do
if ; then
echo "%df is more than $df_threshold "
fi
done (6 Replies)
Discussion started by: aish11
6 Replies
8. Solaris
I have been instructed to disable the finger service for our Solaris 10 box. However when I input #svcadm disable finger I receive: "svcadm: Pattern 'finger' does not match any instances. I have also tried to edit the inetd config file and comment out the finger part but Solaris has basically... (14 Replies)
Discussion started by: mvhoward
14 Replies
9. IP Networking
Dear gurus of Linux / Unix.
I have a server, which I use to monitoring traffic, the problem that I find is when I run the following command:
probe:~ # sar -n DEV 1
I see that I one second appear info in some interface and in the other second no appear, I don't know what will be the... (0 Replies)
Discussion started by: andresguillen
0 Replies
10. Shell Programming and Scripting
Hello Forum,
I have prepared script to monitor the tomcat status.
Following is the script which will monitor tomcat instance.
I need little modifcation in the script.
My script will grep for process,
the output of grep command will analyze by if condition under for loop and will send... (2 Replies)
Discussion started by: ooilinlove
2 Replies
LEARN ABOUT SUSE
nagios
nagios(8) Nagios nagios(8) NAME
Nagios - network/systems status monitoring daemon SYNOPSIS
nagios [-h] [-v] [-s] [-d] <main_config_file> DESCRIPTION
nagios is a daemon program that monitors the status of various network accessible systems, devices, and more. For more information, please consult the online documentation available at http://www.nagios.org, or on your nagios server's web page. OPTIONS
main_config_file The main configuration file. On openSUSE systems this defaults to /etc/nagios/nagios.cfg -h A helpful usage message -v Reads all data in the configuration files and performs a basic verification/sanity check. Always make sure you verify your config data before (re)starting Nagios. You can also use the Nagios init script to verify your configuration - try: rcnagios check_verbose -s Shows projected/recommended check scheduling information based on the current data in the configuration files. -d Starts Nagios in daemon mode (instead of as a foreground process). FILES
/etc/nagios Default configuration directory for nagios AUTHOR
Nagios is written and maintained by Ethan Galstad <nagios@nagios.org>. This manual page was written by sean finney <seanius@debian.org> for the Debian GNU/Linux operating system (but it may be freely used, modified, and redistributed by others) and adapted by Lars Vogdt for openSUSE. sean finney, Lars Vogdt February 2006, May 2010 nagios(8)