Hi,
I am running an oracle db 9.2.0.5.0 on ibm p5 550 aix 5.3 with 10g ram, 10G swap space 3 database instances each SGA about 500Meg.
I am getting the following error in my alert log file from time to time:
skgpspawn failed:category = 27142, depinfo = 11, op = fork, loc = skgpspawn3
... (0 Replies)
My root disk is failed and how to replace the root disk in AIX.
Can u give a detailed explanation in step wise.
Pls give the answer taking different scenarios.
Regards
Praveen (1 Reply)
Hi all,
I installed AIX 5.3 (TL 5300-08-01) and after that I updated to TL 5300-09-01.
The problem is that, when I issue "lppchk -v" I get the following error:
# lppchk -v
lppchk: The following filesets need to be installed or corrected to bring
the system to a consistent state:... (10 Replies)
Hi,
I experience an issue with printer queue configuration and when I tried to verify files of the printer and lpd installable software product, I get these messages:
#lppchk -c
lppchk: 0504-208 Size of /usr/lib/lpd/digest is 44634,
expected value was 44874.
lppchk: 0504-208 Size of... (8 Replies)
Hi,
I am installing bison-2.4.3 on AIX.
I am facing the below error.
Could not load program gawk:
Symbol resolution failed for gawk because:
Symbol __pthread (number 159) is not exported from dependent module /usr/lib/libpthreads.a(shr_xpg5.o).
Symbol libintl_bindtextdomain (number... (5 Replies)
Hello Team,
Hope all doing well. I have tried to upgrade on of my AIX box too the latest SP and TL, but unfortunately it's got failed(Details are below). Need expert help to fix this.
Before up-gradation :
root@# oslevel -s
6100-07-01-1141
root@# instfix -i | grep ML
All... (3 Replies)
I have a AIX 7.1 system that has 3 failed disks, 1 in rootvg and 2 in vg_usr1.
Here is the output of lspv.
# lspv
hdisk0 00044d4dfbb11575 vg_usr1 active
hdisk1 0000150179158027 vg_usr1 active
hdisk2 ... (11 Replies)
im new to aix... my task is suppose to be simple. install openssh
i followed this article:
Installing OpenSSH and OpenSSL on AIX 6.1 | Keymon's snippets and brushstrokes
when i try to start the sshd service with the command: "startsrc -s sshd"
im getting an error saying:
"the sshd subsystem... (6 Replies)
Discussion started by: guy3145
6 Replies
LEARN ABOUT DEBIAN
systemd-volatile-root.service
SYSTEMD-VOLATILE-ROOT.SERVICE(8) systemd-volatile-root.service SYSTEMD-VOLATILE-ROOT.SERVICE(8)NAME
systemd-volatile-root.service, systemd-volatile-root - Make the root file system volatile
SYNOPSIS
systemd-volatile-root.service
/lib/systemd/systemd-volatile-root
DESCRIPTION
systemd-volatile-root.service is a service that replaces the root directory with a volatile memory file system ("tmpfs"), mounting the
original (non-volatile) /usr inside it read-only. This way, vendor data from /usr is available as usual, but all configuration data in
/etc, all state data in /var and all other resources stored directly under the root directory are reset on boot and lost at shutdown,
enabling fully stateless systems.
This service is only enabled if full volatile mode is selected, for example by specifying "systemd.volatile=yes" on the kernel command
line. This service runs only in the initial RAM disk ("initrd"), before the system transitions to the host's root directory. Note that this
service is not used if "systemd.volatile=state" is used, as in that mode the root directory is non-volatile.
SEE ALSO systemd(1), systemd-fstab-generator(8), kernel-command-line(7)systemd 237SYSTEMD-VOLATILE-ROOT.SERVICE(8)