Thanks a lot for that .
lparstat command returned the below when tried from AIX itself
When lparstat command is issued from HMC,it returned the following,
Can you please suggest how i can go further , also can you brief about the mksysb command for me please.Thanks
Hi,
i have to make an excect physical copie of a sun unix station harddisk.
I have to make all partitions the same on about 60 harddisks, and also they should contain the same data/info.
I have hade a look at commands 'DD' and 'UFSDUMP' but both of them are not sufficient enough.
Can... (5 Replies)
I have a Sun Solaris 9 and I would like to clone the Operating System from a sun4u Sun Fire 480R machine to a Sun Fire 280R machine. The disk is the same size, the 480R has no space disk slot to the 280R disk for mirrioring, i have no external disk, I am not allowed to take the machine down.
... (1 Reply)
I've got two drives in the same Sun server and I've been cloning the boot drive to the secondary drive by using both ufsdump/ufsrestore and the dd command sucessfully.
When I try and boot the cloned drive I get the following error:
WARNING - /usr/sbin/fsck not found. Most likely the mount... (10 Replies)
Hello Everyone,
Can someone help me to mount a SAN hdisk which contains a clone data copy(san) of the remote server to the another machine. Both servers are running in AIX.
Thanks in advance !
Regards,
Gowtham.G (3 Replies)
Hello;
Please,I did the clone on virtualBox, but the machines have the same IP address: eth2 Link encap: Ethernet HWaddr 8:00:27: f0: 92:19 inet addr: 192.168.1.4 Bcast: 192.168.1.255 Mask: 255.255.255.0
how to change the address please?
Thank you so much (6 Replies)
the following command will give me software ID from HP machine with hpux10.2:
>uname -a
HP-UX bmd350 B.10.20 D 9000/831 2011043966 64-user license
The string 2011043966 is the actual software ID which is used as number to license software.
Now my machine breaks down and I would like to... (1 Reply)
hello folks,
I have a 300GB ROOTVG volume groups with one filesystem /backup having 200GB allocated space
Now, I cannot alt disk clone or mirrorvg this hdisk with another smaller disk. The disk size has to be 300GB; I tried alt disk clone and mirrorvg , it doesn't work. you cannot copy LVs as... (9 Replies)
Hi,
I'm a new user of this forum and I'm not an expert of linux.
I have a broken old pc with red hat linux, I clone hdd to another pc with different mainboard and it's ok but it has only one problem, the usb ports not work.
In the boot this message appears:
... (9 Replies)
Hello,
I have two AIX machine and i want to make the two nodes to be identical , so i will change the Hostname, IP and copy the hosts file to node 2.
anything else need to copy it from node 1 to node 2 to ensure that two nodes will be the same?
Thanks (8 Replies)
Hello to all,
Im having a new task in a new world (AIX - IBM Servers)
I have an IBM Server (Type - 9111-285 very old one) with one Hard disk (73 GB 10 K) with AIX 5.x, and I need to clone the existing disk to another with the same specifications.
Could you please give me some advice in order... (7 Replies)
Discussion started by: trevian3969
7 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)