Guys
This is what I am getting when booting from a bootable USB stick (biolinux):
- Post updated 06-14-16 at 10:06 PM -
Solved the problem disabling the boot security and enabling legacy. Finally, I rearranged the boot sequence to 1) USB 2) HDD and proceeded to reinstall Biolinux. Worked like a charm!
Does anyone know a good driver site. If you've heard of driverguide.com or driversearch.com please do not reccomend them because I already know them. I need to know where to get Motherboard drivers for a homemade computer. If there is any info that you need to know feel free to make a reply.
:) (5 Replies)
Hello,
I got a computer in which I decided to change RAM memory cards.
These (2) RAMs are:
Brand: Crucial Technology DDR Ram 266 Mhz
and when I ran memtest86 tool, both of them have errors.
So I decided to change them and purchase a new ones.
I bought:
Brand: Patriot DDR RAM 512 Mb 266... (2 Replies)
Hi All,
I installed Ubuntu10.04LTS after using it for some day , a problem started ,at system boot time error is coming
Bad BIOS checksum.Starting BIOS recovery.
checking for floppy.checking for CD is coming repeatedly but system is not cuming up.
After sometime output was also not... (0 Replies)
Hi,
Can anyone please advise how I can reset my BIOS password on my BL460c-class blade?
I need to make some changes but do not know what the password has been set to. This is a newly purchased server so any default I can try may be useful.
R,
D. (3 Replies)
Hi friends,
I hope you are doing well. Can you please tell me which part of the motherboard contains the BIOS software, name that exact location. And could please give me the names of the firmwares for atleast 5 archetictures, like sun sparc, ibm power, hp alpha etc.
Looking forward to your... (0 Replies)
okay,i made a grave mistake in installing the base bare bones install of debian.
here i have edited this from the original.
this morning when i got home from work i did some searching and then just shut the system down via the mechanical off on switch. waited a few minutes and then restarted... (0 Replies)
I need to update a setting in the BIOS on our SCO Openserver 5.0.7 system and all I can bring up about it says I need to create a dos bootable disk of some sort. The problem is that it doesn't seem like dos is loading up fully. I created the dos bootable thumb drive on a Windows PC using Rufus... (7 Replies)
Hi All,
unable to fetch the bios configuration information and service provider information in centos 5 using dmidecode command.
ServiceProvider=`dmidecode -s system-product-name |awk '{print $1}'`
BIOS_Configuration=`dmidecode | grep "BIOS Information" -A10 | grep -e... (4 Replies)
Discussion started by: sravani25
4 Replies
LEARN ABOUT DEBIAN
blockdev
BLOCKDEV(8) System Administration BLOCKDEV(8)NAME
blockdev - call block device ioctls from the command line
SYNOPSIS
blockdev [-q] [-v] command [command...] device [device...]
blockdev --report [device...]
DESCRIPTION
The utility blockdev allows one to call block device ioctls from the command line.
OPTIONS -V Print version and exit.
-q Be quiet.
-v Be verbose.
--report
Print a report for the specified device. It is possible to give multiple devices. If none is given, all devices which appear in
/proc/partitions are shown. Note that the partition StartSec is in 512-byte sectors.
COMMANDS
It is possible to give multiple devices and multiple commands.
--flushbufs
Flush buffers.
--getalignoff
Get alignment offset.
--getbsz
Print blocksize in bytes.
--getdiscardzeroes
Get discard zeroes support status.
--getfra
Get filesystem readahead in 512-byte sectors.
--getiomin
Get minimum I/O size.
--getioopt
Get optimal I/O size.
--getmaxsect
Get max sectors per request
--getpbsz
Get physical block (sector) size.
--getra
Print readahead (in 512-byte sectors).
--getro
Get read-only. Print 1 if the device is read-only, 0 otherwise.
--getsize64
Print device size in bytes.
--getsize
Print device size (32-bit!) in sectors. Deprecated in favor of the --getsz option.
--getss
Print sectorsize in bytes - usually 512.
--getsz
Get size in 512-byte sectors.
--rereadpt
Reread partition table
--setbsz bytes
Set blocksize.
--setfra sectors
Set filesystem readahead (same like --setra on 2.6 kernels).
--setra sectors
Set readahead (in 512-byte sectors).
--setro
Set read-only.
--setrw
Set read-write.
AUTHOR
blockdev was written by Andries E. Brouwer and rewritten by Karel Zak.
AVAILABILITY
The blockdev command is part of the util-linux package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux/.
util-linux August 2010 BLOCKDEV(8)