Recently, I had to disable autoneg in one of my servers having ixgbe1 interface. While using below command I got "Permission denied" error:
On investigating further I found that adv_autoneg_cap is showing as read-only parameter. Although it is read & write parameter in all other servers. But I don't know how it has become read only parameter in this system.
I am trying to set an interface to 100/Full, but the command I use are getting rejected. I think it is the last argument, but I don't know how to find the correct values.
I am trying to use the following script, but change hme to le .
echo "Setting hme interface 1: 100mb/full-duplex..."
... (2 Replies)
Hi Guys,
I need help with ndd.
I was going through network FAQ but i have more questions then answers regarding ndd.
#ndd -set /dev/hme instance 0
#ndd -set /dev/hme adv_100fdx_cap 1
#ndd -set /dev/hme adv_100hdx_cap 0
#ndd -set /dev/hme adv_10fdx_cap 0
#ndd -set /dev/hme adv_10hdx_cap 0... (2 Replies)
Hello Gurus
I would like to know more about ndd commands related to ethernet(NIC) like how to set link_status, link_speed & link_mode as I know how to check these value. And I also would like to know how to make these setting permanents after reboot as I know that these setting will vanish... (5 Replies)
Hi,
Is there any function calls available ( for using in a C program ) to get the Ethernet Link status. ?
I am looking for the status available from
ndd /dev/hme link_status
And how about plumbing and configuring an interface using C program ?
BTW, Is all this documented... (3 Replies)
Hi,
I would like to know whether there is any config file that i can refer to for the result of 'ndd -get /dev/tcp tcp_time_wait_interval'?
When i man 'ndd', there is one statement which is -> Each driver chooses which parameters to make visible using ndd. Does it answering my question above... (3 Replies)
Solaris 10 server (SunOS 5.10 Generic_137137_09)
I have a services file configured in /etc in there windows clients connect to my server on port 6034-6037
when I do the following
netstat | grep TestServices
it pulls all the connections active for those ports
so right now I have 10 clients... (3 Replies)
I have a T2000 server which has 4 e1000g NIC cards
How do I configure each of it for 1Gbit full duplex and turnoff autonegotiation.
Please assist
Thanks (4 Replies)
Following command was set up in startup script on Solaris 8 servers - improved network transfers of files from one server to the another (doubled transfer speed).
ndd -set /dev/tcp tcp_host_param '10.140.20.10 sendspace 279600 recvspace 279600 timestamp 1'
Now they are getting a new server... (15 Replies)
Hello forum,
I have a Solaris 9 Sun Fire v240 server and Sun Fire v440
Recently we made changes and installed a new switch which both of them are connected to it. Cisco Catalyst 3750.
Now the Sun Server v240 is having problems with the network. It was supposed to run at 1000mbs speed.
ndd... (10 Replies)
Discussion started by: br1an
10 Replies
LEARN ABOUT MOJAVE
install-solaris
install-solaris(1M)install-solaris(1M)NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)