06-12-2016
Thank you very much for your responses from both hicksd8 & DukeNuke2 to my question, and I appreciate you. Your information is very useful to me and now I know how to proceed quickly and correctly.
Last edited by DukeNuke2; 06-12-2016 at 05:10 AM..
Reason: Deleted illegel request.
8 More Discussions You Might Find Interesting
1. Solaris
I am new to Sun.
I brought Sun Fire 280R to practice UNIX. What are the requirements for the monitor/CRT? Will it burn out old non-Sun CRTs? Does it need LCD monitor?
Thanks. (3 Replies)
Discussion started by: bramptonmt
3 Replies
2. Solaris
Hello there!
I have Sun Fire 3800 with very old Solaris 9 and I need to perform upgrade to concurrent Solaris 10 version, preserving current OS configuration. I supose to make it using Live Upgrade, but according to Solaris Live Upgrade Software: Minimum Patch Requirements page, I need to... (5 Replies)
Discussion started by: Sapfeer
5 Replies
3. UNIX for Dummies Questions & Answers
Hello people from Argentina i said you Hello.
I am doing some works from an auditory.
They want to disable login prompts on serial ports.
Somebody knows how to do that?
Thank your time. (1 Reply)
Discussion started by: enkei17
1 Replies
4. Solaris
I can't find why but I suppose it is because of some hardware failures... I have a Sun Fire V490 with Solaris 10 5/08 which runs Sun Cluster 3.2 and it downs occasionally with a circumstances I can't define... Also I note some strange behavior after server failures: when I ran any diagnostics from... (6 Replies)
Discussion started by: Sapfeer
6 Replies
5. Solaris
I have a sun fire v240 server.
The output of prtdiag -v shows a failed fan.
There are 3 fans for cooling system board.
There is 1 fan for each of the powersupply (There are 2 powersupplies)
From the below output how do i know which fan is bad and whats its location... (3 Replies)
Discussion started by: Tirmazi
3 Replies
6. Solaris
==============================
ALOM BOOTMON v1.3.1
ALOM Build Release: 001
Reset register: f0000000 EHRS ESRS LLRS SWRS
ALOM POST 1.0
Dual Port Memory Test, PASSED.
TTY External - Internal Loopback Test
TTY External - Internal Loopback Test, PASSED.
TTYC - Internal Loopback Test
TTYC -... (4 Replies)
Discussion started by: Sameer Naik
4 Replies
7. Solaris
Hey Guys I am new here, dont know if any one can assist me with this issue.
I have a Sun-Fire-V490 machine that was upgraded to version 9 and patched a few months back.
Problem is a few network printers managed by the server is printing an extra page that comes out before and after every print... (0 Replies)
Discussion started by: mprogams
0 Replies
8. Solaris
Hi Solaris/Unix Experts,
I've installed Oracle Solaris 10 1/13 on a Sun Fire V490 Server via its external Serial Port using a Cisco Console Cable connected to my Laptop PC running SecureCRT terminal emulation software emulating VT100 Terminal.
The Sun Fire V490 server has two on-board... (1 Reply)
Discussion started by: ssabet
1 Replies
LEARN ABOUT LINUX
debconf-set-selections
DEBCONF-SET-SELECTIONS(1) Debconf DEBCONF-SET-SELECTIONS(1)
NAME
debconf-set-selections - insert new default values into the debconf database
SYNOPSIS
debconf-set-selections file
debconf-get-selections | ssh newhost debconf-set-selections
DESCRIPTION
debconf-set-selections can be used to pre-seed the debconf database with answers, or to change answers in the database. Each question will
be marked as seen to prevent debconf from asking the question interactively.
Reads from a file if a filename is given, otherwise from stdin.
WARNING
Only use this command to seed debconf values for packages that will be or are installed. Otherwise you can end up with values in the
database for uninstalled packages that will not go away, or with worse problems involving shared values. It is recommended that this only
be used to seed the database if the originating machine has an identical install.
DATA FORMAT
The data is a series of lines. Lines beginning with a # character are comments. Blank lines are ignored. All other lines set the value of
one question, and should contain four values, each separated by one character of whitespace. The first value is the name of the package
that owns the question. The second is the name of the question, the third value is the type of this question, and the fourth value (through
the end of the line) is the value to use for the answer of the question.
Alternatively, the third value can be "seen"; then the preseed line only controls whether the question is marked as seen in debconf's
database. Note that preseeding a question's value defaults to marking that question as seen, so to override the default value without
marking a question seen, you need two lines.
Lines can be continued to the next line by ending them with a "" character.
EXAMPLES
# Force debconf priority to critical.
debconf debconf/priority select critical
# Override default frontend to readline, but allow user to select.
debconf debconf/frontend select readline
debconf debconf/frontend seen false
OPTIONS
--verbose, -v
verbose output
--checkonly, -c
only check the input file format, do not save changes to database
SEE ALSO
debconf-get-selections(1) (available in the debconf-utils package)
AUTHOR
Petter Reinholdtsen <pere@hungry.com>
2011-06-22 DEBCONF-SET-SELECTIONS(1)