hi guys..
i have a shell script that loops through a certain directory to see if a file has been created and then prints the file if it exists...
the only problem i have now is that sometimes the flat does not get created by the program thats supposed to create it, in this scenario, my loop... (1 Reply)
having problems using scp in that during peak hours it appears to time out.
anyone have similar experiences? any thoughts regarding a solution... (1 Reply)
I need to make it so an autmated process which involves ssh, times out if ssh prompts for a password. Most of the time it shouldnt prompt for a password. But if it does i need it to time it out or get a status and stop the ssh and log that the ssh failed and move onto the next server. Is there any... (9 Replies)
hi everyone. If you have a function created in your code and you want to find out how long it takes for it to run you can use a struct called gettimeofday().
so lets say we have a function like this
int myfunction (int r)
{
/*some math calculations*/
return answer;
}
How do i set up... (3 Replies)
Hello and thanks in advance.
I have a Sun box with raid 1 on the O/S disks using solaris svm.
I want to unmirror my swap partition, and add the slice on the second disk as an additional swap device. This would give me twice as much swap space.
I have been warned not to do this by some... (3 Replies)
In my server migration requirement, I need to compare if one file on old server is exactly the same as the corresponding file on the new server.
For diff and comm, the inputs need to be sorted. But I do not want to disturb the content of the file and need to find byte-to-byte match.
Please... (4 Replies)
Hi All
Can anyone please suggest me how to remove the last byte from a falt file .This is from the last line's last BYTE.
Please suggest me something.
Thank's and regards
Vinay (1 Reply)
Hi
I have an integrity machine rx7620 and rx8640 running hp-ux 11.31. I'm planning to fine tune the system:
- I would like to know when does the memory swap space spill over to the device swap space?
- And how much % of memory swap utilization should be specified (swap space device... (6 Replies)
i have a very big script i have that i'd like to add a timeout to.
this script runs on a several remote host. i update this script with timeout clause and then copy it over to all the hosts on which it is currently on.
basically, i want the timeout to make the script abort/exit if it's... (1 Reply)
Hi Solaris Folks :),
I need to calculate the swap usage on solaris server, please let me understand the output of below swap -s and swap -l commands.
$swap -s
total: 1774912k bytes allocated + 240616k reserved = 2015528k used, 14542512k available
$swap -l
swapfile dev swaplo... (6 Replies)
Discussion started by: seenuvasan1985
6 Replies
LEARN ABOUT HPUX
swapmem_on
swapmem_on(5) OBSOLETE swapmem_on(5)NAME
swapmem_on - OBSOLETE kernel tunable parameter
DESCRIPTION
The tunable is obsolete. Processes will always be allowed to use pseudo-swap space if it is available.
In previous versions of HP-UX, system configuration required sufficient physical swap space for the maximum possible number of processes on
the system. This is because HP-UX reserves swap space for a process when it is created, to ensure that a running process never needs to be
killed due to insufficient swap.
This was difficult, however, for systems needing gigabytes of swap space with gigabytes of physical memory, and those with workloads where
the entire load would always be in core. This tunable was created to allow system swap space to be less than core memory. To accomplish
this, a portion of physical memory is set aside as "pseudo-swap" space. While actual swap space is still available, processes still
reserve all the swap they will need at fork or execute time from the physical device or file system swap. Once this swap is completely
used, new processes do not reserve swap, and each page which would have been swapped to the physical device or file system is instead
locked in memory and counted as part of the pseudo-swap space.
WARNINGS
Installation of optional kernel software, from HP or other vendors, may cause changes to tunable parameter values. After installation,
some tunable parameters may no longer be at the default or recommended values. For information about the effects of installation on tun-
able values, consult the documentation for the kernel software being installed. For information about optional kernel software that was
factory installed on your system, see at
AUTHOR
was developed by HP.
Tunable Kernel Parameters swapmem_on(5)