You will now have net0 inside your ldom uatenv which is using primary-vsw.
Of course, you will still need to add disk devices.
In case of card/port failure or a switch failure, all the ldoms will lose network connectivity.
Hope that helps.
Best regards
Peasant.
Thanks for your reply.
Eventually I figured out the solution.
Here it is..
1. Add a new virtual switch
2. Plumb the interface
3. Assign IP and up the interface
4. Modify the existing vnet so that it can listen the new virtual switch
ldm set-vnet vswitch= primary-vsw1 vnet0 ldom03
vnet0 is interface for old switch.
Later after doing tests, I will again set vnet0 to old switch.
Hi,
I have issues installing Solaris into a LDom using a Solaris10u5/08 DVD. I have been troubleshooting for the past 2 days and I still cannot get it up.
Here is the logs:
root@eld-app2# ldm add-vdsdev /cdrom/sol_10_508_sparc/s0 cdrom0@primary-vds0
root@eld-app2# ldm add-vdisk cdrom0... (4 Replies)
Trying to set or modify the randomly set hostID of a Solaris 10 virtual/guest machine that I installed on a Windows-XP host machine (using Virtual Box 4.1.12).
I was able to set/modify the hostname of the Solaris 10 virtual/guest machine during installation as well as via the Virtual Box... (4 Replies)
Apologies if this is the wrong forum..
I have some LDOMs running on a Sparc server. I copied the disk0 file from one chassis over to another, stopped the ldom on the source system and started it on the 2nd one. All fine. Shut it down and flipped back. We then did a fair bit of work on the... (4 Replies)
Hello,
I am trying to install Solaris 10 on a newly created LDom. Here are the commands I ran to create the LDom:
ldm add-domain ldg2
ldm add-vcpu 8 ldg2
ldm add-memory 2g ldg2
ldm add-vnet vnet2 primary-vsw0 ldg2
ldm add-vdsdev /dev/dsk/c0t5000CCA01535E20Cd0s0 vol2@primary-vds0
ldm... (8 Replies)
I have an Oracle VM set up with 1 virtual disk. I am trying to add 2 new disks to it. I was able to successfully add 1 (it appears when I run "format" in the VM) but when I add the second and third disks they do not appear in my VM.
Here are the commands I ran:
ldm add-vdsdev... (3 Replies)
hello, I have a problem when configuring the network at the LDOM level, on a SPARC-Enterprise-T5120 machine
The network goes through VLAN 503 (level, network tagget)
And I need to give network to the guest domain: madarrwebsol10
I hope someone can bring some light ....
Excuse my English ...
... (4 Replies)
Hello Guys,
Can some help me with a configuration from 2x10g cards to 4 Ldoms and a Vlan configuration,
Solaris 11
dladm show-phys
LINK MEDIA STATE SPEED DUPLEX DEVICE
net0 Ethernet up 1000 full ixgbe0
net1 Ethernet ... (2 Replies)
I have a Sun T4-1 running Solaris 11.4 with a static IP 192.168.0.183. On this machine is a Solaris 10 LDOM with a static IP of 192.168.0.78. The other day I had to stop the LDOM to do a memory reconfigure. When I rebooted it I got an error that the IP 192.168.0.78 was already in use and so... (4 Replies)
Discussion started by: Michele31416
4 Replies
LEARN ABOUT CENTOS
struct_rio_switch
STRUCT RIO_SWITCH(9) Internals STRUCT RIO_SWITCH(9)NAME
struct_rio_switch - RIO switch info
SYNOPSIS
struct rio_switch {
struct list_head node;
u16 switchid;
u8 * route_table;
u32 port_ok;
int (* add_entry) (struct rio_mport *mport, u16 destid, u8 hopcount,u16 table, u16 route_destid, u8 route_port);
int (* get_entry) (struct rio_mport *mport, u16 destid, u8 hopcount,u16 table, u16 route_destid, u8 *route_port);
int (* clr_table) (struct rio_mport *mport, u16 destid, u8 hopcount,u16 table);
int (* set_domain) (struct rio_mport *mport, u16 destid, u8 hopcount,u8 sw_domain);
int (* get_domain) (struct rio_mport *mport, u16 destid, u8 hopcount,u8 *sw_domain);
int (* em_init) (struct rio_dev *dev);
int (* em_handle) (struct rio_dev *dev, u8 swport);
int (* sw_sysfs) (struct rio_dev *dev, int create);
struct rio_dev * nextdev[0];
};
MEMBERS
node
Node in global list of switches
switchid
Switch ID that is unique across a network
route_table
Copy of switch routing table
port_ok
Status of each port (one bit per port) - OK=1 or UNINIT=0
add_entry
Callback for switch-specific route add function
get_entry
Callback for switch-specific route get function
clr_table
Callback for switch-specific clear route table function
set_domain
Callback for switch-specific domain setting function
get_domain
Callback for switch-specific domain get function
em_init
Callback for switch-specific error management init function
em_handle
Callback for switch-specific error management handler function
sw_sysfs
Callback that initializes switch-specific sysfs attributes
nextdev[0]
Array of per-port pointers to the next attached device
AUTHOR
Matt Porter <mporter@kernel.crashing.org>, <mporter@mvista.com>
Author.
COPYRIGHT Kernel Hackers Manual 3.10 June 2014 STRUCT RIO_SWITCH(9)