Sponsored Content
Operating Systems AIX Need Help with SDD / SDDPCM / MPIO Post 302973769 by filosophizer on Saturday 21st of May 2016 03:44:41 PM
Old 05-21-2016
Firmware on DS4300 is 6.0.3.x
ALready checked the compatibility matrix

I am trying to upgrade vios to the latest version and will check what happens and post here so everyone can benefit

upgraded ios

Code:
# oslevel -s
6100-09-06-1543

$ ioslevel
2.2.4.10

Code:
manage_disk_drivers -d DS4500 -o AIX_APPCM
manage_disk_drivers -d DS4300 -o AIX_APPCM

did not work

---------- Post updated at 11:44 AM ---------- Previous update was at 12:36 AM ----------

Problem resolved

Code:
# fget_config -Av

---dar0---

User array name = ''
dac0 ACTIVE dac2 ACTIVE

Disk     DAC   LUN Logical Drive
utm             31
hdisk8   dac0    0 1
hdisk9   dac2    1 2
# lsdev -p fcs0
fcnet0 Defined   0A-08-01 Fibre Channel Network Protocol Device
fscsi0 Available 0A-08-02 FC SCSI I/O Controller Protocol Device
# lsdev -p fscsi0
dac0     Available 0A-08-02    1722-600 (600) Disk Array Controller
sfwcomm0 Available 0A-08-02-FF Fibre Channel Storage Framework Comm
#

# manage_disk_drivers -l
Device              Present Driver        Driver Options
2810XIV             AIX_AAPCM             AIX_AAPCM,AIX_non_MPIO
DS4100              AIX_APPCM             AIX_APPCM,AIX_fcparray
DS4200              AIX_APPCM             AIX_APPCM,AIX_fcparray
DS4300              AIX_fcparray          AIX_APPCM,AIX_fcparray
DS4500              AIX_fcparray          AIX_APPCM,AIX_fcparray
DS4700              AIX_APPCM             AIX_APPCM,AIX_fcparray
DS4800              AIX_APPCM             AIX_APPCM,AIX_fcparray
DS3950              AIX_APPCM             AIX_APPCM
DS5020              AIX_APPCM             AIX_APPCM
DCS3700             AIX_APPCM             AIX_APPCM
DS5100/DS5300       AIX_APPCM             AIX_APPCM
DS3500              AIX_APPCM             AIX_APPCM
XIVCTRL             MPIO_XIVCTRL          MPIO_XIVCTRL,nonMPIO_XIVCTRL
2107DS8K            NO_OVERRIDE           NO_OVERRIDE,AIX_AAPCM,AIX_non_MPIO
IBMFlash            NO_OVERRIDE           NO_OVERRIDE,AIX_AAPCM,AIX_non_MPIO
IBMSVC              NO_OVERRIDE           NO_OVERRIDE,AIX_AAPCM,AIX_non_MPIO
#

# lsdev -Cc disk
hdisk0 Available 09-08-00-3,0 16 Bit LVD SCSI Disk Drive
hdisk1 Available 09-08-00-4,0 16 Bit LVD SCSI Disk Drive
hdisk2 Available 09-08-00-5,0 16 Bit LVD SCSI Disk Drive
hdisk3 Available 09-08-00-8,0 16 Bit LVD SCSI Disk Drive
hdisk4 Available 09-08-01-3,0 16 Bit LVD SCSI Disk Drive
hdisk5 Available 09-08-01-4,0 16 Bit LVD SCSI Disk Drive
hdisk6 Available 09-08-01-5,0 16 Bit LVD SCSI Disk Drive
hdisk7 Available 09-08-01-8,0 16 Bit LVD SCSI Disk Drive
hdisk8 Available 0A-08-02     1722-600 (600) Disk Array Device
hdisk9 Available 0B-08-02     1722-600 (600) Disk Array Device

manage_disk_drivers -d DS4300 -o AIX_fcparray

if DS4300 doesn;t work


manage_disk_drivers -d DS4500 -o AIX_fcparray


Last edited by filosophizer; 05-30-2016 at 02:43 PM..
 

10 More Discussions You Might Find Interesting

1. Solaris

IBM SDD on Sun

I just installed IBMsddsun64_........... on my sun server. I untarred it (tar xvf) & I tried to install the paxkage. When I did pkgadd -d ./IBMsdd..... I get a message Error, no packages were found. Any idea Thanks, (1 Reply)
Discussion started by: Remi
1 Replies

2. UNIX for Advanced & Expert Users

Help with SDD, SAN ESS and AIX 5.3 Host

Hi all, Sorry if this is in the wrong place but needed to make sure lots of people saw this so that hopefully someone will be able to help. Basically i've upgraded a test server from 4.3 to 5.3 TL04. The server has hdisk0 and 1 as rootvg locally but then has another vg setup on our ESS... (1 Reply)
Discussion started by: djdavies
1 Replies

3. Filesystems, Disks and Memory

SDD for SVC on HP-UX and LINUX

Hello Unix Admins: Has any one in this distribution list implemented SVC (SAN Volume Contoller - A solution from IBM) in your environment? If you have, do you have any do's / don'ts? Anything which you like sharing would be really appreciated. For example, my inputs: I tried implementing... (1 Reply)
Discussion started by: kdossjojo
1 Replies

4. AIX

SDD SDDPCM MPIO lspath Jargon

Can anyone recommend me some reading material surrounding how AIX handles LUNs: - with and without MPIO installed - with and without SDD or SDDPCM installed Where does lspath sit in all of this (MPIO layer?). Can a system be built with just MPIO software? Is MPIO software even needed? I guess... (0 Replies)
Discussion started by: apra143
0 Replies

5. Red Hat

IBM SDD driver

I was wondering if there is a way of auto-detecting a new vpath, using IBM's SDD driver, on a Linux platform. ON AIX it is a simple as running cfgmgr. Alan (0 Replies)
Discussion started by: alanp
0 Replies

6. AIX

AIX with SDD to VIOed SDDPCM?

Hi folks. We want to move a "physical" AIX box to a VIOed LPAR. The physical box is running SDD with disks from a DS8300. I want to be able to reattach those LUNs from the DS8300 to my VIO server which is running SDDPCM and then assigned them back to my AIX LPAR. Any thoughts about this? I... (1 Reply)
Discussion started by: Stephan
1 Replies

7. AIX

AIX SDD

I have sdd driver installed correctly but when I run the command: datapath query adapter No device file found what does it mean.. it is not using vpath or whats wrong? (2 Replies)
Discussion started by: Vit0_Corleone
2 Replies

8. AIX

Upgrading from native MPIO to SDDPCM AIX 6.1

We have AIX 6.1 system attached to SAN disks (DS4700 and DS8100) thru SVC. Initially when the system was I forgot to install sddpcm drivers. and wanted to know how can i go with the installation of the sddpcm drivers. My understandin going thru the manual ... (3 Replies)
Discussion started by: mk8570
3 Replies

9. AIX

sddpcm on vio

I have same lun (hdisk3) assigned to 2 vios server (dual vio server) and this is mapped to the client lpar. I have sddpcm on the VIO. On the VIOA, the attributes for fscsi1 and fscsi3 are set to fast_fail and dyntrk is set to yes Now, if I do a lqueryvg -Atp on the hdisk3, I get a "DISK... (4 Replies)
Discussion started by: mk8570
4 Replies

10. AIX

hdisk status in sdd volume groups

hi all we recently upgraded our san switches. after that, i found i got many hdisks showing in lsdev with status "Defined" and "Available". the number of "Defined" is equal to "Available". the time stamp shows all "Available" disks created at our downtime night. "datapath query device"... (0 Replies)
Discussion started by: rs6000er
0 Replies
PERLAIX(1)						 Perl Programmers Reference Guide						PERLAIX(1)

NAME
README.aix - Perl version 5 on IBM Unix (AIX) systems DESCRIPTION
This document describes various features of IBM's Unix operating system (AIX) that will affect how Perl version 5 (hereafter just Perl) is compiled and/or runs. Compiling Perl 5 on AIX When compiling Perl, you must use an ANSI C compiler. AIX does not ship an ANSI compliant C-compiler with AIX by default, but binary builds of gcc for AIX are widely available. At the moment of writing, AIX supports two different native C compilers, for which you have to pay: xlC and vac. If you decide to use either of these two (which is quite a lot easier than using gcc), be sure to upgrade to the latest available patch level. Currently: xlC.C 3.1.4.10 or 3.6.6.0 or 4.0.2.2 or 5.0.2.9 or 6.0.0.3 vac.C 4.4.0.3 or 5.0.2.6 or 6.0.0.1 note that xlC has the OS version in the name as of version 4.0.2.0, so you will find xlC.C for AIX-5.0 as package xlC.aix50.rte 5.0.2.0 or 6.0.0.3 subversions are not the same `latest' on all OS versions. For example, the latest xlC-5 on aix41 is 5.0.2.9, while on aix43, it is 5.0.2.7. Perl can be compiled with either IBM's ANSI C compiler or with gcc. The former is recommended, as not only can it compile Perl with no difficulty, but also can take advantage of features listed later that require the use of IBM compiler-specific command-line flags. The IBM's compiler patch levels 5.0.0.0 and 5.0.1.0 have compiler optimization bugs that affect compiling perl.c and regcomp.c, respec- tively. If Perl's configuration detects those compiler patch levels, optimization is turned off for the said source code files. Upgrading to at least 5.0.2.0 is recommended. If you decide to use gcc, make sure your installation is recent and complete, and be sure to read the Perl README file for more gcc-spe- cific details. Please report any hoops you had to jump through to the development team. OS level Before installing the patches to the IBM C-compiler you need to know the level of patching for the Operating System. IBM's command 'oslevel' will show the base, but is not always complete (in this example oslevel shows 4.3.NULL, whereas the system might run most of 4.3.THREE): # oslevel 4.3.0.0 # lslpp -l | grep 'bos.rte ' bos.rte 4.3.3.75 COMMITTED Base Operating System Runtime bos.rte 4.3.2.0 COMMITTED Base Operating System Runtime # The same might happen to AIX 5.1 or other OS levels. As a side note, perl cannot be built without bos.adt.syscalls and bos.adt.libm installed # lslpp -l | egrep "syscalls|libm" bos.adt.libm 5.1.0.25 COMMITTED Base Application Development bos.adt.syscalls 5.1.0.36 COMMITTED System Calls Application # Building Dynamic Extensions on AIX AIX supports dynamically loadable objects as well as shared libraries. Shared libraries by convention end with the suffix .a, which is a bit misleading, as an archive can contain static as well as dynamic members. For perl dynamically loaded objects we use the .so suffix also used on many other platforms. Note that starting from Perl 5.7.2 (and consequently 5.8.0) and AIX 4.3 or newer Perl uses the AIX native dynamic loading interface in the so called runtime linking mode instead of the emulated interface that was used in Perl releases 5.6.1 and earlier or, for AIX releases 4.2 and earlier. This change does break backward compatibility with compiled modules from earlier perl releases. The change was made to make Perl more compliant with other applications like Apache/mod_perl which are using the AIX native interface. This change also enables the use of C++ code with static constructors and destructors in perl extensions, which was not possible using the emulated interface. The IBM ANSI C Compiler All defaults for Configure can be used. If you've chosen to use vac 4, be sure to run 4.4.0.3. Older versions will turn up nasty later on. For vac 5 be sure to run at least 5.0.1.0, but vac 5.0.2.6 or up is highly recommended. Note that since IBM has removed vac 5.0.2.1 through 5.0.2.5 from the software depot, these versions should be considered obsolete. Here's a brief lead of how to upgrade the compiler to the latest level. Of course this is subject to changes. You can only upgrade ver- sions from ftp-available updates if the first three digit groups are the same (in where you can skip intermediate unlike the patches in the developer snapshots of perl), or to one version up where the `base' is available. In other words, the AIX compiler patches are cumulative. vac.C.4.4.0.1 => vac.C.4.4.0.3 is OK (vac.C.4.4.0.2 not needed) xlC.C.3.1.3.3 => xlC.C.3.1.4.10 is NOT OK (xlC.C.3.1.4.0 is not available) # ftp ftp.software.ibm.com Connected to service.boulder.ibm.com. : welcome message ... Name (ftp.software.ibm.com:merijn): anonymous 331 Guest login ok, send your complete e-mail address as password. Password: ... accepted login stuff ftp> cd /aix/fixes/v4/ ftp> dir other other.ll output to local-file: other.ll? y 200 PORT command successful. 150 Opening ASCII mode data connection for /bin/ls. 226 Transfer complete. ftp> dir xlc xlc.ll output to local-file: xlc.ll? y 200 PORT command successful. 150 Opening ASCII mode data connection for /bin/ls. 226 Transfer complete. ftp> bye ... goodbye messages # ls -l *.ll -rw-rw-rw- 1 merijn system 1169432 Nov 2 17:29 other.ll -rw-rw-rw- 1 merijn system 29170 Nov 2 17:29 xlc.ll On AIX 4.2 using xlC, we continue: # lslpp -l | fgrep 'xlC.C ' xlC.C 3.1.4.9 COMMITTED C for AIX Compiler xlC.C 3.1.4.0 COMMITTED C for AIX Compiler # grep 'xlC.C.3.1.4.*.bff' xlc.ll -rw-r--r-- 1 45776101 1 6286336 Jul 22 1996 xlC.C.3.1.4.1.bff -rw-rw-r-- 1 45776101 1 6173696 Aug 24 1998 xlC.C.3.1.4.10.bff -rw-r--r-- 1 45776101 1 6319104 Aug 14 1996 xlC.C.3.1.4.2.bff -rw-r--r-- 1 45776101 1 6316032 Oct 21 1996 xlC.C.3.1.4.3.bff -rw-r--r-- 1 45776101 1 6315008 Dec 20 1996 xlC.C.3.1.4.4.bff -rw-rw-r-- 1 45776101 1 6178816 Mar 28 1997 xlC.C.3.1.4.5.bff -rw-rw-r-- 1 45776101 1 6188032 May 22 1997 xlC.C.3.1.4.6.bff -rw-rw-r-- 1 45776101 1 6191104 Sep 5 1997 xlC.C.3.1.4.7.bff -rw-rw-r-- 1 45776101 1 6185984 Jan 13 1998 xlC.C.3.1.4.8.bff -rw-rw-r-- 1 45776101 1 6169600 May 27 1998 xlC.C.3.1.4.9.bff # wget ftp://ftp.software.ibm.com/aix/fixes/v4/xlc/xlC.C.3.1.4.10.bff # On AIX 4.3 using vac, we continue: # lslpp -l | grep 'vac.C ' vac.C 5.0.2.2 COMMITTED C for AIX Compiler vac.C 5.0.2.0 COMMITTED C for AIX Compiler # grep 'vac.C.5.0.2.*.bff' other.ll -rw-rw-r-- 1 45776101 1 13592576 Apr 16 2001 vac.C.5.0.2.0.bff -rw-rw-r-- 1 45776101 1 14133248 Apr 9 2002 vac.C.5.0.2.3.bff -rw-rw-r-- 1 45776101 1 14173184 May 20 2002 vac.C.5.0.2.4.bff -rw-rw-r-- 1 45776101 1 14192640 Nov 22 2002 vac.C.5.0.2.6.bff # wget ftp://ftp.software.ibm.com/aix/fixes/v4/other/vac.C.5.0.2.6.bff # Likewise on all other OS levels. Then execute the following command, and fill in its choices # smit install_update -> Install and Update from LATEST Available Software * INPUT device / directory for software [ vac.C.5.0.2.6.bff ] [ OK ] [ OK ] Follow the messages ... and you're done. If you like a more web-like approach, a good start point can be http://www14.software.ibm.com/webapp/download/downloadaz.jsp and click "C for AIX", and follow the instructions. Using GNU's gcc for building perl Using gcc-3.x (tested with 3.0.4, 3.1, and 3.2) now works out of the box, as do recent gcc-2.9 builds available directly from IBM as part of their Linux compatibility packages, available here: http://www.ibm.com/servers/aix/products/aixos/linux/ Using Large Files with Perl Should yield no problems. Threaded Perl Threads seem to work OK, though at the moment not all tests pass when threads are used in combination with 64bit configurations. 64-bit Perl If your AIX is installed with 64-bit support, you can expect 64bit configurations to work. In combination with threads some tests might still fail. AIX 4.2 and extensions using C++ with statics In AIX 4.2 Perl extensions that use C++ functions that use statics may have problems in that the statics are not getting initialized. In newer AIX releases this has been solved by linking Perl with the libC_r library, but unfortunately in AIX 4.2 the said library has an obscure bug where the various functions related to time (such as time() and gettimeofday()) return broken values, and therefore in AIX 4.2 Perl is not linked against the libC_r. AUTHOR
H.Merijn Brand <h.m.brand@hccnet.nl> DATE
Version 0.0.6: 23 Dec 2002 perl v5.8.0 2003-02-18 PERLAIX(1)
All times are GMT -4. The time now is 11:41 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy