I'm trying to mirror 2 eide disks on a solaris 10 x86 system.
Im trying to use the prtvtoc | fmthard command to mirror the vtoc.
How do they represent the entire disk like in solaris 9 (c0t0d0s2 = entire device)
0. c0d0 <DEFAULT cyl 26497 alt 2 hd 16 sec 63>
... (1 Reply)
Hello,
I am trying to do mirror in solaris 9. I have total 0-7 disks
4 5 6 7
0 1 2 3
Drive 0 and Drive 4 = Boot Drives
Need to Mirror following drives.
Drive 1 and Drive 5 = Need to mirror
Drive 1 was mounted on: /prod1, /prod2, /prod3, /prod4, /prod5.
Then i... (3 Replies)
Hi,
am a newbie at solaris. Need advice and help on this.
1) How do I break the mirror between 2 hard disks. (wish to keep 1 good hard disk as backup)
2) After remove 1 hard disk and put in new hard disk, how do I initialise or fomat the new hard disk?
3) How do I put back the backup... (3 Replies)
I am having an issue with setting up disk mirroring for Solaris 10 on an x86 server. My main problem is that the volumes and slices have already been setup and our proprietary software has already been installed and configured. The entire drive has been allocated in this configuration and the... (2 Replies)
Hi everyone,
Normally it always easier in Sparc machine, i can set or manually use the boot-device in NVram to boot the mirrored disk. However I have a big trouble about x86 mirror for a long time. I have been doing anything i can: search document, google, ask the others.
Recently i did as... (5 Replies)
I’m setting up a boot disk mirror on Solaris 10 x86. I’m used to doing it on SPARC, where you can copy the partition table using fmthard. My x86 boot disk has 2 primary partitions, a Solaris one and a diagnostic one. Is there a way to copy those 2 primary partitions to the second disk without... (6 Replies)
hi friends, need help.. it is my first time patching using mirror disk backup approach, not so sure about the steps :confused: how do you detach, patch it, boot it and reattach it ? any kind soul here can advise ? thanks in advance..:)
below is the information from my machine:
Filesystem ... (3 Replies)
Hi,
Can you help me on booting x86 server configured under VxVM. Server boots fine normally from both the disks but if I try to boot server from mirror disk without starting veritas, then it does not boot.
vxplex -g rootdg dis var-02
vxplex -g rootdg dis swapvol-02
vxplex -g rootdg dis... (2 Replies)
hi all!
i extend disk on SPARC solaris without problems, but with x86 Solaris 10 i have some troubles . Help pls
iostat show me updated disk size, but in format i can't choose Auto configure options to use modified slice
# iostat -E c0d1
cmdk1 Soft Errors: 0 Hard Errors: 0 Transport... (4 Replies)
Discussion started by: ijj
4 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)