Sponsored Content
Special Forums IP Networking Default/saved-telemetry-pings Post 302971965 by 1in10 on Wednesday 27th of April 2016 02:48:52 PM
Old 04-27-2016
following the link, I will disable it for good, nontheless I don' t need it and updates of any kind did not work fine always. Thanks a lot for the hint and the link!!!!!!!!
 

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Sudo file not saved

Hi all, I have edited my sudoers file. I am using visudo command I have added the following lines and saved the file. I am saving the lines as :wq But I am very amazed to see that these lines are not written in the sudoers file. I have retried the above process many times, when I... (0 Replies)
Discussion started by: Asteroid
0 Replies

2. Shell Programming and Scripting

Can STDERR be saved to a variable

Guys i'm trying to save STDERR to a variable for a portion of my ksh script on solaris. I know i can create redirects to files as such: exec 4>/tmp/lava print "This will be saved to /tmp/lava and not screen"; >&4 print "This will be seen on screen" >&2 I want to save the STDOUT of a... (4 Replies)
Discussion started by: lavascript
4 Replies

3. UNIX and Linux Applications

Bluefish: where are the preferences saved?

I have just tried out Bluefish as an alternative to my regular text editor. If I save the modified preferences and reboot, the preferences have to be reentered again. Does anyone know which file the preferences are saved in? The command find / -mmin -5 | grep bluefish yields zero hits. Thanks... (2 Replies)
Discussion started by: figaro
2 Replies

4. UNIX for Dummies Questions & Answers

where alias saved?

step 1 # alias alias cp='cp -i' alias l.='ls -d .* --color=tty' alias ll='ls -l --color=tty' alias ls='ls --color=tty' alias mv='mv -i' alias rm='rm -i' alias which='alias | /usr/bin/which --tty-only --read-alias --show-dot --show-tilde' step 2 # cat ~/.bashrc # .bashrc (3 Replies)
Discussion started by: cqlouis
3 Replies

5. UNIX for Dummies Questions & Answers

Advice on automating mass pings and retrieving the summary times from each ping

Hi guys, Bit of a Unix amateur here! :b: As part of some research I'm doing I am looking into performance differences between IPv4 and IPv6, and have a list of IPv6 accessible websites and their respective v4 and v6 addresses. I'm looking to do a ping to each one and record, for each... (2 Replies)
Discussion started by: churchill
2 Replies

6. UNIX for Dummies Questions & Answers

Script Not getting Saved

Hi , Script File Is Not Getting Saved This Are The Steps I Am Following For Saving And Executing A Script 1). vi ( To Open Vi Editor ) 2). vi filename ( vi firstprog.ksh) #!bin\kash date 3) !wq :( Saving And Quit) When I Am Saving The Scrpit I Am Getting The Below... (1 Reply)
Discussion started by: anudeepkumar123
1 Replies

7. Solaris

Aliases not getting saved in OK prompt

Hi Guys, After setting below paths: ok nvalias rootdisk /pci@1c,600000/scsi@2/disk@0,0:a ok nvalias rootmirror /pci@1c,600000/scsi@2/disk@1,0:a ok nvstore to check: ok devalias devailas does show set path but after reboot The alias for disks are not getting saved. I get this error:-... (5 Replies)
Discussion started by: manalisharmabe
5 Replies

8. Shell Programming and Scripting

How to extract info from pings.?

Hi guys, new to this forum. I am currently trying to extract the times from pinging a domain and list the top 3 and then also do the opposite i.e. list the bottom 3. so if I had this as a ping result (the bold part is what I want): 64 bytes from 193.120.166.90: icmp_seq=10 ttl=128 time=34.8... (5 Replies)
Discussion started by: acoding
5 Replies

9. Shell Programming and Scripting

Squares in saved code

can you help i am merging 2 files together and saving to a third file with awk and its working with this code awk 'OFS="";NR==FNR{a=$0;next} {print a,"\n","\b",$0}' file1 file2 > file3the problem is in file3 when its saved i get a small square at the start of every 2nd line (see picture) ... (6 Replies)
Discussion started by: bob123
6 Replies
link(1) 						      General Commands Manual							   link(1)

NAME
link, unlink - Creates an additional directory entry for an existing file SYNOPSIS
link file1 file2 unlink file STANDARDS
Interfaces documented on this reference page conform to industry standards as follows: link: XCU5.0 unlink: XCU5.0 Refer to the standards(5) reference page for more information about industry standards and associated tags. DESCRIPTION
The link command performs the link() system call to create an additional directory entry for an existing file, file1. In effect, the underlying file then has two names, file1 and file2 (either of these arguments can be a pathname). The old and new entries share equal access rights to the underlying file. The unlink command performs the unlink() system call to remove a link to file created by link. The unlink command removes the directory entry specified by the file parameter and, if the entry is a hard link, decrements the link count of the file referenced by the link. You should be familiar with the link() and unlink() system calls before you use these commands. The link and unlink commands do not issue error messages when the associated system call is unsuccessful. NOTES
The link and unlink commands cannot be used to link and unlink directories. EXIT STATUS
The link and unlink commands both exit with the following: The link() or unlink() system call succeeded. Too few or too many arguments specified. The link() or unlink() system call failed. SEE ALSO
Commands: fsck(8), ln(1) Functions: link(2), unlink(2) link(1)
All times are GMT -4. The time now is 07:14 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy