04-19-2016
Thank you. I can reboot only by switching the power off. Unfortunatly :-(.
Do you have an idea what cause the problem?
Thanks, Chris
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi,
We have a SunFire V880, hooked up with 2 T3 arrays. When ever we issue a reboot command on the system, it hangs at the same place right where it says
syncing file systems done.
To bring it back we shutdown power and it comes clean.
By the way init 6 command works fine.
Has anyone come... (3 Replies)
Discussion started by: smohd
3 Replies
2. Solaris
Hi all,
I have a SUN server Sun-Fire-V890 running solaris 9, with a remote system console .
Both the IP adresses of the server and the console are in a private network (address 10.67.xxx).
For some reasons I need to give the access to the server from outside address 194.xxx, but I prefer that... (2 Replies)
Discussion started by: aribault
2 Replies
3. Solaris
Hello,
I downloaded the vmware image of Solaris 10 Update 3 from the Sun site. I have a problem with vim when I edit a file while being connected through SSH to my vm:
When I try to edit whatever file with vim, it freezes just after I've hit enter.
vim works correctly when I run it in a... (1 Reply)
Discussion started by: Tex-Twil
1 Replies
4. Solaris
Greetings Forumers!
I tried installing Solaris Cluster 3.3 today. I should say I tried configuring the Cluster today. The software is already installed on two systems. I am trying to configure a shared filesystem between two 6320 Blades. I selected the "Custom" install because the "Typical"... (2 Replies)
Discussion started by: bluescreen
2 Replies
5. Solaris
Hi,
We've got a Sun Fire V245 that's failing to boot from either boot disk (mirrored using SVM). It simply hangs after loading a few modules:
Sun Fire V245, No Keyboard
Copyright 2006 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.22.22, 1024 MB memory installed, Serial... (5 Replies)
Discussion started by: badoshi
5 Replies
6. Solaris
Solaris 10 (Sun V210) System hangs every couple of months. Have to go into ALOM to reset. I did a consolehistory report and seen this in it.
Failed to exec inetd_start method of instance svc:/network/bootps/udp:default: I/O error
WARNING: /pci@1c,600000/scsi@2 (glm0):
Resetting... (3 Replies)
Discussion started by: Joeentech
3 Replies
7. Shell Programming and Scripting
Hi All,Our sftp connection from Solaris to windows 2008 hangs with following verbose output. From the output I can see that the connection itself ( key matching ) is successful , but I can't see sftp prompt.Sun_SSH_1.1.3, SSH protocols 1.5/2.0, OpenSSL 0x0090704f
debug1: Reading configuration data... (1 Reply)
Discussion started by: rahulkav
1 Replies
8. Solaris
Got a strange problem.
I have 4 Solaris servers all configured the same, Solaris 10 x86 update 10.
When I try to ssh from one Solaris 10 server to another server ssh hangs.
I have an identical server and when I try this everything works fine.
The weird thing is if I am root on the server... (1 Reply)
Discussion started by: ccj4467
1 Replies
9. Solaris
Power server up runs through diagnostics.
Goes to the boot section and then the bit where the cursor is spinning and thats it. Hangs completely.
Any ideas? (10 Replies)
Discussion started by: psychocandy
10 Replies
10. Solaris
Anyone ever see an issue where ufsdump 'hangs' after the IV Pass?
Normally, it will update with an estimate of how long it will take to complete...and update the info every 20 minutes.
I'm running the following command:
root# ufsdump 0f - /fsmount | ( cd /zfs/newfsmount ) ; ufsrestore rf - )... (2 Replies)
Discussion started by: RTM
2 Replies
LEARN ABOUT ULTRIX
reboot
reboot(8) System Manager's Manual reboot(8)
Name
reboot - automatic reboot procedures
Syntax
/etc/reboot [ -n ] [ -q ]
Description
The ULTRIX system is booted by loading a kernel image, usually into memory at location zero and transferring to zero. Because the system
is not reenterable, the kernel image must be read in from disk each time the system is bootstrapped.
When the reboot of a running system is desired, is normally used. If there are no users, can be used. The command causes the disks to be
synced, and then a multiuser reboot is initiated. The system is booted and an automatic disk check is performed. If the procedure suc-
ceeds, the system is then brought up for the users.
The system will reboot itself after a power failure or after a crash, provided auto-restart is enabled on your system. A consistency check
of the file systems will be performed and, unless the check fails, the system will resume multiuser operations.
Options
-n Prevents the disks from being synced.
-q Reboots quickly and ungracefully, without shutting down running processes first.
Files
System code
See Also
crash(8v), fsck(8), halt(8), init(8), newfs(8), rc(8), shutdown(8)
reboot(8)