I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output.
You haven't said which system you use but from the output format i suppose it is some Linux-derivate.
It is common to configure network interfaces in via scripts/scriptlets in /etc/sysconfig/... but i suppose (part of) your configuration (the old part) is/was also duplicated in some other part of the system initialisation, probably in some rc-script somewhere in /etc/rc.d. Perhaps this didn't show p because the two competing configurations were effectively the same. Now that you have changed one of them they create two different configurations.
If this is the case you should simply remove that other configuration and rely on /etc/sysconfig and the procedures using it.
Hi gurus,
In a few month, we must enable IPv6 on our Linux Server!
Should we reinstall the Linux machine to enable IPv6 or could we just make some change in configuration's files?
Could Linux run simultaneous IPv4 and IPv6?
Thanks in advance for our help our ideas?
Best regards,
nm (3 Replies)
Hi, anyone has had experience in a static setting an IPv6 interface?, I'm trying accordance with the admin guide (ipv6 network configuration tasks), configure one interface in the server, actually i can do ping to my default gateway and access the Internet in IPv6, the specific point is however,... (3 Replies)
Hi,
Apologies if this is the wrong forum or this question has been answered already.
I'm using the ISC dhcpd server on Centos 6.0, and can happily assign a single IPV6 address to a client with entries like this:
subnet6 fd01:0:0:5::/64
{
option dhcp6.name-servers fd01:0:0:5::226;... (0 Replies)
Hi,
Can any one please help me increase the arp stale time of an ipv6 interface on linux platform ?
I have tried increasing the variable gc_stale_time but that doesnt work.
Thanks (2 Replies)
Hello all,
I am trying to receive (tcp/udp/sctp) traffic from all IPs and, eventually, all ports of an IPv6 address block using as few sockets as possible short of implementing my own network stack.
One possible solution was to associate an IP block to an interface then bind to that... (6 Replies)
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Hello Dears ,
please I need your support I have Oracle Solaris 10 X86 server please if you can advise how can I add IP v6 on my server and if IPv6 was disabled how can i enable it also how can i add two IP (v4 and v6) on the same interface or I have to add another interface .
Thanks in... (1 Reply)
I'm running a Linux OS that uses Debian as it's base. A commercial vpn is installed that uses OpenVPN. For some reason, I can't get ipv6 to tunnel properly .... and Ipleak.net shows that my location is being unmasked by ipv6.
I've tried kernel commands at boot, I've tried sysctl.conf commands.... (2 Replies)
Discussion started by: benc
2 Replies
LEARN ABOUT DEBIAN
mstack
VIEW-OS(1) General Commands Manual VIEW-OS(1)NAME
mstack - networking stack selection
SYNOPSIS
mstack [-hv] [-o protocol list] stack_mountpoint command
DESCRIPTION
In View-OS multiple networking stacks are available to processes at the same time. View-OS supports the msocket(2) system call. mstack
defines the default stack (for each address family) that is used when msocket refers to a NULL pathname for its stack. mstack provides
also a backward compatibility for all the programs using the obsolete socket(2) system call. The stack mountpoint identifies the stack. In
ViewOS it is the mountpoint where the stack was mounted (by mount(2)(8). In fact the call:
"socket(domain,type,protocol)"
is equivalent to:
"msocket(NULL,domain,type protocol)"
mstacks changes the default stack for the desired protocol families and executes the command (by execve(2)).
OPTIONS -h prints the mstack command usage
-v sets the verbose mode on
-o defines the list of protocols. Without a -o option, mstack redefines the default stack for all protocols families. The list of proto-
cols may include the a comma separated sequence of the following items: all, unix (or simply u), ipv4 (4), ipv6 (6), netlink (n),
packet (p), bluetooth (b), irda (i), ip (which include all ip related protocols ipv4, ipv6, netlink and packet), #n where n is the num-
ber of protocol. Each item can be prefixed by + or - to specify whether the protocol/group of protocols must be added or removed from
the set.
EXAMPLES
mstack /dev/net/lwip ip addr
lists the address managed by the stack mounted on /dev/net/lwip.
exec mstack /dev/net/null bash
disables the standard stack in a new bash (which overcomes the current one).
mstack -o ip /dev/net/lwip bash
starts a new bash which uses the stack /dev/net/lwip for ipv4 and ipv6 but not for the other protocols.
mstack -o -unix /dev/net/lwip bash
starts a new bash which uses the stack /dev/net/lwip for all protocols but AF_UNIX.
mstack -o +ip,-ipv6 /dev/net/lwip bash
starts a new bash which uses the stack /dev/net/lwip for ipv4, netlink, packet but not ipv6.
SEE ALSO umview(1), kmview(1), msocket(3), umnetnative(9), umnetnull(9), umnetlwipv6(9), unix(7), ip(7), ipv6(7), netlink(7), packet(7).
AUTHORS
View-OS is a project of the Computer Science Department, University of Bologna. Project Leader: Renzo Davoli.
<http://www.sourceforge.net/projects/view-os>
Howto's and further information can be found on the project wiki <wiki.virtualsquare.org>.
VIEW-OS: a process with a view April 23, 2008 VIEW-OS(1)