Just give it the directory as an argument; not all of the files in the directory as separate arguments. I.e., change:
to:
and, you can get the same results with:
and, it will run a LOT faster if you use -exec command initial-args {} + to minimize the number of times you invoke rm:
These 2 Users Gave Thanks to Don Cragun For This Post:
Hi,
I want to find the exit status of the last executed command in C Shell.
Tried $? but getting the error Variable syntax...$? does not seem to work in C shell..
is there any other command in C shell to find the exit status of last command?
Thanks in advance,
raju (1 Reply)
I am executing a find command in my script i.e
find $2 -type f -name '*.gif' -mtime +$1 -exec rm {} \;
how do i check that this command is executed properly.. i would lke t trap the errror and display my error message
kinly help.. this is an urgent issue. (1 Reply)
Hi All,
I am checking for a empty input file to do some further action , but I am getting exit status 0 in both the cases , for empty and non empty file both.
The value of $? is coming 0 in if part also and else part too.
#!/bin/ksh
if ]; then
echo "data"
# exit 0
echo "$?"
else... (4 Replies)
Hi,
Want to log the output of command & check the exit status to find whether it succeeded or failed.
> ls abc
ls: abc: No such file or directory
> echo $?
1
> ls abc 2>&1 | tee log
ls: abc: No such file or directory
> echo $?
0
Tee commands changes my exit status to be always... (7 Replies)
I need to find empty files in a directory and write them into a text file. Directory will contain old files as well, i need to get the empty files for the last one hour only. (1 Reply)
My code to "Delete empty files from a directory entered in command promt"
#/bin/sh
echo "Enter directory"
read gh
for file in `ls $gh`
do
# to get the size of file
a=$( ls -l file | awk ' {print $7} ');
echo $a
if
then
echo "removing file "
rm file
fi
done (6 Replies)
Hello All,
I am trying to capture the exit status of find command and want to delete the files only when it is successful. But it is always returning me as success even if the pattern of that file doesn't exist in the current directory. please help, checked manual page but couldn't able to figure... (6 Replies)
I have the following code in a script:
find . \( ! -name . -prune \) -name "cg*" -exec cp -p {} "${temp_dir}" \;
ret_stat=$?
I think the return status is only captured for the 'find' command and not for the 'cp' command. Is there a way to get the return status for the 'cp' command... (7 Replies)
In a fastload teradata utility I am trying to delete the files which are older than 30days using the find and rm command as following.
find . -name 'xxx_*' -mtime +30 -exec rm -f {} \;
I expect it to delete all the files older than 30 days but sometimes it gives an error : find: bad status--... (3 Replies)
Discussion started by: stelkar
3 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)