UKBD(4) 						   BSD Kernel Interfaces Manual 						   UKBD(4)

NAME

     ukbd -- USB keyboard driver

SYNOPSIS

     To compile this driver into the kernel, place the following line in your kernel configuration file:

	   device ukbd

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   ukbd_load="YES"

DESCRIPTION

     The ukbd driver provides support for keyboards that attach to the USB port.  usb(4) and one of uhci(4) or ohci(4) must be configured in the
     kernel as well.

CONFIGURATION

     By default, the keyboard subsystem does not create the appropriate devices yet.  Make sure you reconfigure your kernel with the following
     option in the kernel config file:

	   options KBD_INSTALL_CDEV

     If both an AT keyboard USB keyboards are used at the same time, the AT keyboard will appear as kbd0 in /dev.  The USB keyboards will be kbd1,
     kbd2, etc.  You can see some information about the keyboard with the following command:

	   kbdcontrol -i < /dev/kbd1

     or load a keymap with

	   kbdcontrol -l keymaps/pt.iso < /dev/kbd1

     See kbdcontrol(1) for more possible options.

     You can swap console keyboards by using the command

	   kbdcontrol -k /dev/kbd1

     From this point on, the first USB keyboard will be the keyboard to be used by the console.

     If you want to use a USB keyboard as your default and not use an AT keyboard at all, you will have to remove the device atkbd line from the
     kernel configuration file.  Because of the device initialization order, the USB keyboard will be detected after the console driver initial-
     izes itself and you have to explicitly tell the console driver to use the existence of the USB keyboard.  This can be done in one of the fol-
     lowing two ways.

     Run the following command as a part of system initialization:

	   kbdcontrol -k /dev/kbd0 < /dev/ttyv0 > /dev/null

     (Note that as the USB keyboard is the only keyboard, it is accessed as /dev/kbd0) or otherwise tell the console driver to periodically look
     for a keyboard by setting a flag in the kernel configuration file:

	   device sc0 at isa? flags 0x100

     With the above flag, the console driver will try to detect any keyboard in the system if it did not detect one while it was initialized at
     boot time.

DRIVER CONFIGURATION

	   options KBD_INSTALL_CDEV

     Make the keyboards available through a character device in /dev.

	   options UKBD_DFLT_KEYMAP
	   makeoptions UKBD_DFLT_KEYMAP=fr.iso

     The above lines will put the French ISO keymap in the ukbd driver.  You can specify any keymap in /usr/share/syscons/keymaps with this
     option.

	   options KBD_DISABLE_KEYMAP_LOADING

     Do not allow the user to change the keymap.  Note that these options also affect the AT keyboard driver, atkbd(4).

FILES

     /dev/kbd*	blocking device nodes

EXAMPLES

	   device ukbd

     Add the ukbd driver to the kernel.

SEE ALSO

     kbdcontrol(1), ohci(4), syscons(4), uhci(4), usb(4), config(8)

AUTHORS

     The ukbd driver was written by Lennart Augustsson <augustss@cs.chalmers.se> for NetBSD and was substantially rewritten for FreeBSD by
     Kazutaka YOKOTA <yokota@zodiac.mech.utsunomiya-u.ac.jp>.

     This manual page was written by Nick Hibma <n_hibma@FreeBSD.org> with a large amount of input from Kazutaka YOKOTA
     <yokota@zodiac.mech.utsunomiya-u.ac.jp>.

BSD
								 November 22, 2006							       BSD