03-23-2016
9 More Discussions You Might Find Interesting
1. Solaris
Hi
I am unable to understand the disk layout of one of my disk attached to v240. This is newly installed system from jumpstart.
I am unable to see the free space on backup slice 2 and there are 0 to 8 slices listed when I run format and print the disk info, also there is no reference of... (9 Replies)
Discussion started by: kumarmani
9 Replies
2. Solaris
I'd like to finish setting up this system and then move the secondary or primary disk to another system that is the exact same hardware.
I've done things like this in the past with ufs and disk suite mirroring just fine. But I have yet to do it with a zfs root pool mirror.
Are there any... (1 Reply)
Discussion started by: Metasin
1 Replies
3. Solaris
Hi,
I have Solaris-10 (release-7) box without any non global zone. I have a very critical change after couple of days from application side. For safer side, we want to keep few level of backups just in case of faliure. This server is having three pool
root@prod_ddoa01:/# zpool list
NAME SIZE... (2 Replies)
Discussion started by: solaris_1977
2 Replies
4. Red Hat
Hi,
I have installed RHEL6 on a HP Dl360 with 2 x 300G disk drives.
The logical volume (SMART ARRY) uses RAID 0+1.
All file systems occupy a max of 50G in disk space leaving 250G free disk space. A possible 100G will get used for the application later.
My question is, will creating a... (1 Reply)
Discussion started by: Duffs22
1 Replies
5. Solaris
Hi everyone,
I am doing housekeeping of my Solaris 11 for zfs snapshot to reduce the snapshot size. I have already cleared the / file system, however the rpool size still not reduced.
Filesystem Size Used Available Capacity Mounted on
rpool/ROOT/solaris-2 98G 6.9G ... (2 Replies)
Discussion started by: freshmeat
2 Replies
6. Solaris
Hi,
I have this fresh installation of Solaris 11.3 sparc.
I have two zfs pools both using two disks in mirroring mode, both are online.
I want to move /system/zones, currently rpool/VARSHARE/zones, from rpool to the other zfs pool so my zones don't consume space on the disks allocated to... (1 Reply)
Discussion started by: X96
1 Replies
7. Solaris
hi,
have no a lot of experience with zfs so perhaps the question is quite simple but i didn't find any reasonable info how to resolve it.
thus, fresh solaris installation
14GB in 86 files copied after that got msg No space left on device (28) in spite of according to stat there is... (4 Replies)
Discussion started by: bindto
4 Replies
8. Solaris
I have a 240GB disk as rpool. I have installed Solaris 11.3 to a partition which is 110GB. Now I have another 130GB which is unallocated. I want to use that additional space as a temporary folder to be shared between Solaris and Linux. The additional space had no /dev/dsk/c2t4... entry so I used... (8 Replies)
Discussion started by: kebabbert
8 Replies
9. UNIX for Advanced & Expert Users
Hi Folks!
Its been a while since I worked with ZFS but basically, I need to monitor free space for Solaris 10 & 11 systems (with & without zones)
I am hoping that any space commands only need to be run from the global zone (to simplify matters)
However, I'm not not sure if there are exceptions... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT V7
ppmtosixel
ppmtosixel(1) General Commands Manual ppmtosixel(1)
NAME
ppmtosixel - convert a portable pixmap into DEC sixel format
SYNOPSIS
ppmtosixel [-raw] [-margin] [ppmfile]
DESCRIPTION
Reads a portable pixmap as input. Produces sixel commands (SIX) as output. The output is formatted for color printing, e.g. for a DEC
LJ250 color inkjet printer.
If RGB values from the PPM file do not have maxval=100, the RGB values are rescaled. A printer control header and a color assignment table
begin the SIX file. Image data is written in a compressed format by default. A printer control footer ends the image file.
OPTIONS
-raw If specified, each pixel will be explicitly described in the image file. If -raw is not specified, output will default to com-
pressed format in which identical adjacent pixels are replaced by "repeat pixel" commands. A raw file is often an order of magni-
tude larger than a compressed file and prints much slower.
-margin
If -margin is not specified, the image will be start at the left margin (of the window, paper, or whatever). If -margin is speci-
fied, a 1.5 inch left margin will offset the image.
PRINTING
Generally, sixel files must reach the printer unfiltered. Use the lpr -x option or cat filename > /dev/tty0?.
BUGS
Upon rescaling, truncation of the least significant bits of RGB values may result in poor color conversion. If the original PPM maxval was
greater than 100, rescaling also reduces the image depth. While the actual RGB values from the ppm file are more or less retained, the
color palette of the LJ250 may not match the colors on your screen. This seems to be a printer limitation.
SEE ALSO
ppm(5)
AUTHOR
Copyright (C) 1991 by Rick Vinci.
26 April 1991 ppmtosixel(1)