Hi Everybody,
I want to know the names & locations of the common AIX files which it's size keep growing. I think there is a procedure to clean these files to avoid the space overflow, I wish also if anybody can tell me what is the proper procedure to make more available space.
Another issue, that... (2 Replies)
my /etc/.osm file is growing rapidly and logging large amounts of activity. Can anyone tell me what this file is for and what types of information is logged in this file.
Thanks in advance for your help!! (1 Reply)
Hi,
I have an iSCSI LUN of 200GB. I increased it to 250GB and when I try to increase the size of the vg, I'm getting an error that none of the volumes have increased in size.
How can I get the OS to see the additional 50GB?
---------- Post updated at 03:22 PM ---------- Previous update... (9 Replies)
Hi gurus
Im a newbie in solaris..I need to extend file system space in solaris 10 which is using SVM..I have a file system /pin02 which is 93% full n needs to be extended..only 3.6 gb avail space left..the file system is not mirrored...normal ufs file system only..can u please tel me t... (6 Replies)
Hi,
/opt on my disk is almost 90%. I thought of growing it. I followed the below procedure:
1. added a new hard disk
2. formatted the same with ufs
3. created a slice and tried to label it as "opt" with "wm" permissions.
but got stuck at 3 as it is not allowing me to label the slice... (9 Replies)
Greeting Forumers!
I've been asked to increase space in a FS that is currently 740G in size:
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d664 740G 424G 308G 58% /ora_back
My SAN administrator has allocated 5 LUNs of 200G each - this will make... (3 Replies)
Ok so I just installed Solaris 10 on my x86 laptop. But I too the defaults and now all of the FS's are very small. I can't install anything. The drive is a 40GB but only about 11GB is being seen and used. How can I get the OS to see and use the rest of the drive? I was just going to reinstall, but... (3 Replies)
I am trying to be pro-active and prevent FS from filling up. I know about
the df/du command also find -size -mtime .......
What I want to know is there a way I can do a find to see which files have been accessed or modified after a specifc YYYYMMDD-HHMMSS. What I am really looking for is to... (4 Replies)
Hi,
I have a LUN presented to a Linux system and would like to ask if someone can advise if the logical volume /dev/mapper/VGOra-LVOra 12G 11G 659M 95% /usr/app/oracle can be extended. Is there any free space to allocate.... The LUN (25G) has been configured as follows:
LUN - ROOT...... (4 Replies)
I'm having a strange Phenomenon here in one of my servers /usr file system is growing fast and it went wild.
I have searched the entire file system for large , growing and newly created files with no clue what's going on I have found nothing strange.
Any further idea
a snapshot from df's ... (4 Replies)
Discussion started by: h@foorsa.biz
4 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)