I've been googling for a while now, trying to forward port 3000 to port 80....
In the past I used to DLink router to forward port 3000 to 80. I recently finished (well, is it ever done anyhow?) setting up my linux box and got it acting as a router.
I want to continue to run Apache on port 80... (1 Reply)
Hi,
I have to install an application that has a built in tftp server. Tftp comes in on port 69. As i am not installing this application as a root user i am running into trouble because only the root user can listen to ports < 1024. So changing the port i listen to to one greater than 1023 isn't... (1 Reply)
Hi friends
i have the following setup
machine1 two network adapters one connected to lan the other connected directly to machine2
machine2 is not connected to lan
i need to access machine2 directly from the LAN
how to force machine1 to forward all traffic received on a specific port the... (1 Reply)
Hi
I want to set up port forwarding from one network to another network. I already have this configured on the Linux box using iptables.
iptables -t nat -A PREROUTING -p tcp -i eth1 --dport 1521 -j DNAT --to 10.218.146.230
iptables -A FORWARD -p tcp -i eth1 -d 10.218.146.230 -j ACCEPT
... (2 Replies)
Hi,
I am looking out a way to forward all UDP traffic coming on ports 3001,3002,3003 and 3004 on server 10.2.45.200
to
corresponding ports of server 10.2.45.197.
I am using Solaris 10.0.
-bash-3.00$ uname -a
SunOS airtelussd2 5.10 Generic_127127-11 sun4u sparc SUNW,Sun-Fire-V445
Is... (6 Replies)
Hi; I have the following issue:
I have a Solaris server running an old applications which connects to an http server in other server at certain port. The thing is that the http server has changed its ip and port and the addres in the app is hard coded and touching the app by now is out of the... (0 Replies)
Hi Linux/Unix Guru,
I am setting Linux Hopping Station to another different servers.
My current config to connect to another servers is using different port to connect.
e.g
ssh -D 1080 -p 22 username@server1.com
ssh -D 1081 -p 22 username@server2.com
Now what I would like to have... (3 Replies)
hi guys
i have a simple question !
i have two ips . a valid and internal(172.16.11.2)
i want to use port forwarding to forward any request to valid IP port 8001 to internal ip port 80 .
i use this rule :
sysctl -w net.ipv4.ip_forward=1
iptables -t nat -A PREROUTING -p tcp... (1 Reply)
Hello Gurus,
I have configured port forwarding at router.
But after configuration I am not able to connect the computer from outside/Over internet/Remote desktp from other computer.
Could you please advice?
Thanks-
Pokhraj (2 Replies)
Hello All,
I would like to ask you very kindly with /etc/sysconfig/iptables file
I have to setup port forwarding on RHEL6 router. Users from public network must be able to ssh to servers in private network behind RHEL6 router. Problem is that servers in private network must be isolated.
My... (2 Replies)
Discussion started by: oidipus
2 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)