Using a Modem on a T5-2 or a T5240 Post: 302969009

Sponsored Content

Operating Systems Solaris Using a Modem on a T5-2 or a T5240 Post 302969009 by gull04 on Thursday 17th of March 2016 03:46:44 AM

03-17-2016

Registered User

Using a Modem on a T5-2 or a T5240

Hi Folks,

Just a quick question - hopefully!

I have an application currently running on a V890 with Solaris 9, I'd like to move this to either one of our T-5's or one of the T5240's in a Legacy container on an LDOM - but the fly in the ointment is the application still uses a standard Hayes dial-up modem.

Obviously the T-5 is the best option here for going forward, but the T5240 has a DB9 connector and it can be used as a TTYA device.

There's a couple of things that I'd like to ask.

Has anyone connected a serial modem to a T-5 using a USB/Serial converter.
Has anyone connected a serial modem to a T5240 and passed it through to an LDOM.

Or has anyone got any pointers to information with guidance, it's obviously not done very often nowadays.

Regards and TIA

Gull04

Last edited by gull04; 03-17-2016 at 04:48 AM.. Reason: More information.

gull04

View Public Profile for gull04

Visit gull04's homepage!

Find all posts by gull04

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Modem - Test /dev/modem

Ok. I tried following the directions from some of the other threads, but I've hit a road block. I have red hat 7.3 and I installed the hcf package: hcfpcimodem-0.99lnxtbeta03042700k2.4.18_3-1rh.i386.rpm It installed ok, no errors, but I still can't get linux to find my modem. I've tried...

2. Solaris

raidctl on SUN T5240

Setting up a T5240 with two disks c1t0d0 and c1t1d0. I am trying to use raidctl but when I issue. raidctl -l I get Controller 1 Disk: 0.0.0 Disk: 0.1.0 So I try raidctl -c '0.0.0 0.1.0' -r 1 1 and I get "Array in use." I try

3. Solaris

cannot plumb nxge on T5240

its a fresh installation. during the OS setup, it did not prompt for IP, netmask and gateway. using Solaris 10 08/07 update 4. I tried to plumb manually but encountered no such interface error. but nxge interfaces can be greped from the /etc/path_to_inst file. getting similar error on...

4. Solaris

SUN T5240 vs M3000

Hi, We are planning to buy new server for our data center. Sun T5240 or M3000 which one have better performance, we are going to create many dt sessions in this server. So, i need your suggestions. RJS

5. Solaris

ufsrestore T5240

Hi Friends we have sun T5240 server, we have taken ufsdump of this server remotely with scsi tapedrive, If we need to do ufsrestore means what we have to do, since T5240 has not having scsi port, any procedure is there? Regards Rajasekar

6. Solaris

Bizarre Sun T5240 behavior

Hi - I have a T5240 with 7 LDOMS configured. One night, network comm was broken somehow. Nobody was doing anything on the machine at the time. Here is what I saw in messages: WARNING: nxge3 : nxge_dma_mem_alloc: ddi_dma_mem_alloc kmem alloc failed WARNING: nxge3 : nxge_alloc_rx_buf_dma:...

7. Solaris

Disable multithreading option on T5240

Hi Gurus Can any one tell me the process of disabling the multithreading option on T5240 server and my OS is on LDOM, having one physical processor with 8 core & 8 thread per core Regards

8. Solaris

Cannot configure RAID on T5240

Hi ! I've been given a T5240 with 4 disks and 2 HBA cards (but no array connected). I did a factory reset on SP and NVRAM clean on OBP because the server had been used before. I boot cdrom in single mode and try to create a hw mirror with disks from c1... but only c2 is seen by raidctl. ...

9. Solaris

Question: # of ldoms on T5240 with 2 T2 US 8 core

I have a T5240 with 2 T2 US 8 core.. Theoretically how many ldoms can I configure?

LEARN ABOUT REDHAT

serial_cs

SERIAL_CS(4)						     Kernel Interfaces Manual						      SERIAL_CS(4)

NAME

       serial_cs - PCMCIA serial port driver

SYNOPSIS

       insmod serial_cs.o [pc_debug=n] [irq_list=i,j,...]  [do_sound=n]

DESCRIPTION

       Serial_cs  is  the Card Services driver for all PCMCIA serial devices, including modem cards.  When serial_cs is bound to a serial or modem
       card, it will generally attempt to allocate the first unused serial device for use by the card.	The device chosen will be recorded in  the
       kernel log file, and will also be reported to cardmgr(8).  The major and minor numbers and device name reported by serial_cs will match the
       corresponding "dialout" device (/dev/cua#).  The new device can be accessed using this device file or the corresponding /dev/ttyS#  device.
       The default serial card setup script will link the dialout device to /dev/modem.

PARAMETERS

       pc_debug=n
	      Selects  the PCMCIA debugging level.  This parameter is only available if the module is compiled with debugging enabled.	A non-zero
	      value enables debugging.

       irq_list=i,j,...
	      Specifies the set of interrupts that may be allocated by this driver.

       do_sound=n
	      A flag specifying if speaker output should be enabled.  The default is 1 (true).	Set to 0 to disable speaker output.

AUTHOR

       David Hinds - dahinds@users.sourceforge.net

SEE ALSO

       cardmgr(8), pcmcia(5).

pcmcia-cs							2000/06/12 21:24:48						      SERIAL_CS(4)