03-12-2016
Did you activate the new BE?
What's the output of the lustatus before reboot?
The new BE should be activated, from what I see it's not active on reboot.
7 More Discussions You Might Find Interesting
1. Solaris
Hello,
I started the upgrade using LiveUpgrade. I am using Solaris 10 instalation CDs (5 CDs). My server is Enterprise 3500 - SPARC.
1) lucreate -c first_disk -m /:/dev/dsk/c0t11d0s7:ufs -n second_disk
...
luupgrade -u -n second_disk -s /cdrom/cdrom0/s0
WARNING: <5> packages failed to... (0 Replies)
Discussion started by: zafyil
0 Replies
2. Solaris
My Solaris machine is not booting.It just stops at the point
Boot device: /pci@1e,600000/ide@d/disk@0,0:a File and args:
Whether i try boot or boot -s it is stopping at this point..
I tried boot cdom -s.It went into single user mode but I am not able to run a fsck in this mode.
Right... (1 Reply)
Discussion started by: lydiaEd
1 Replies
3. Solaris
I got this output from a system running solaris 10 :
# lustatus
BE_name Complete Active ActiveOnReboot CopyStatus
--------------------------------------------------------------------------------
oldvol yes yes yes -
newvol no no no -
bigvol no no no -
#
How do i remove (or... (1 Reply)
Discussion started by: ibroxy
1 Replies
4. Solaris
OK, latest in a loooong trail of errors with no information. I've finally gotten a new BE created on another drive, run liveupgrade on it to bring it from sol10u3 to sol10u8
I luactivate sol10u8
lustatus shows the sol10u8 as the active one
init 6
system just starts into 10u3 again.
I'm... (4 Replies)
Discussion started by: awoodby
4 Replies
5. UNIX for Dummies Questions & Answers
Folks;
I have a Solaris 9 server that after power outage it won't come fully up and i was able to bring it up in single user mode and checked "/var/log/messages" & "/var/adm/messages" with nothing showing since Sept. 17.
i ran fsck and no luck.
I ran all tests from the OK prompt with no luck... (2 Replies)
Discussion started by: Katkota
2 Replies
6. Solaris
What type of communication does Solaris 10/09 need to do with it's default gateway before it can boot up? (7 Replies)
Discussion started by: bstauffer
7 Replies
7. Solaris
Hi all,
I have got a few questions on the above topic ->
q1) if my intention for creating an ABE is just to use for patching / patchset update -
e.g. ./installpatchset -B secondboot --s10patchset
luactivate secondboot
What is the recommendation that my ABE should consist of ?... (5 Replies)
Discussion started by: javanoob
5 Replies
reboot(2) System Calls Manual reboot(2)
NAME
reboot - boot the system
SYNOPSIS
DESCRIPTION
causes the system to reboot. howto is a mask of reboot options (see specified as follows:
A file system sync is performed (unless
is set) and the processor is rebooted from the default device and file.
The processor is simply halted.
A sync of the file system is performed unless the flag is set. should be used with caution.
On systems with cellular architecture, all cells in the partition are
rebooted in order to reconfigure the stable complex configuration data. On systems with non-cellular architec-
ture, the default is A sync of the file system is performed unless the flag is set.
Shut down the system firmware to a "ready to reconfigure" state and do not
reboot. This option can be used only in combination with
A sync of the file system is not performed.
Unless the flag has been specified, reboot(2) unmounts all mounted file systems and marks them clean so that it will not be necessary to
run fsck(1M) on these file systems when the system reboots.
Only users with appropriate privileges can reboot a machine.
RETURN VALUE
If successful, this call never returns. Otherwise, a -1 is returned and is set to indicate the error.
ERRORS
fails if this condition is encountered:
[EPERM] The effective user ID of the caller is not a user with appropriate privileges.
DEPENDENCIES
The default file and device for is on the current root device.
AUTHOR
was developed by HP and the University of California, Berkeley.
SEE ALSO
reboot(1M), privileges(5).
reboot(2)