03-12-2016
Did you activate the new BE?
What's the output of the lustatus before reboot?
The new BE should be activated, from what I see it's not active on reboot.
7 More Discussions You Might Find Interesting
1. Solaris
Hello,
I started the upgrade using LiveUpgrade. I am using Solaris 10 instalation CDs (5 CDs). My server is Enterprise 3500 - SPARC.
1) lucreate -c first_disk -m /:/dev/dsk/c0t11d0s7:ufs -n second_disk
...
luupgrade -u -n second_disk -s /cdrom/cdrom0/s0
WARNING: <5> packages failed to... (0 Replies)
Discussion started by: zafyil
0 Replies
2. Solaris
My Solaris machine is not booting.It just stops at the point
Boot device: /pci@1e,600000/ide@d/disk@0,0:a File and args:
Whether i try boot or boot -s it is stopping at this point..
I tried boot cdom -s.It went into single user mode but I am not able to run a fsck in this mode.
Right... (1 Reply)
Discussion started by: lydiaEd
1 Replies
3. Solaris
I got this output from a system running solaris 10 :
# lustatus
BE_name Complete Active ActiveOnReboot CopyStatus
--------------------------------------------------------------------------------
oldvol yes yes yes -
newvol no no no -
bigvol no no no -
#
How do i remove (or... (1 Reply)
Discussion started by: ibroxy
1 Replies
4. Solaris
OK, latest in a loooong trail of errors with no information. I've finally gotten a new BE created on another drive, run liveupgrade on it to bring it from sol10u3 to sol10u8
I luactivate sol10u8
lustatus shows the sol10u8 as the active one
init 6
system just starts into 10u3 again.
I'm... (4 Replies)
Discussion started by: awoodby
4 Replies
5. UNIX for Dummies Questions & Answers
Folks;
I have a Solaris 9 server that after power outage it won't come fully up and i was able to bring it up in single user mode and checked "/var/log/messages" & "/var/adm/messages" with nothing showing since Sept. 17.
i ran fsck and no luck.
I ran all tests from the OK prompt with no luck... (2 Replies)
Discussion started by: Katkota
2 Replies
6. Solaris
What type of communication does Solaris 10/09 need to do with it's default gateway before it can boot up? (7 Replies)
Discussion started by: bstauffer
7 Replies
7. Solaris
Hi all,
I have got a few questions on the above topic ->
q1) if my intention for creating an ABE is just to use for patching / patchset update -
e.g. ./installpatchset -B secondboot --s10patchset
luactivate secondboot
What is the recommendation that my ABE should consist of ?... (5 Replies)
Discussion started by: javanoob
5 Replies
HALT(8) halt HALT(8)
NAME
halt, poweroff, reboot - Halt, power-off or reboot the machine
SYNOPSIS
halt [OPTIONS...]
poweroff [OPTIONS...]
reboot [OPTIONS...]
DESCRIPTION
halt, poweroff, reboot may be used to halt, power-off or reboot the machine.
OPTIONS
The following options are understood:
--help
Prints a short help text and exits.
--halt
Halt the machine, regardless of which one of the three commands is invoked.
-p, --poweroff
Power-off the machine, regardless of which one of the three commands is invoked.
--reboot
Reboot the machine, regardless of which one of the three commands is invoked.
-f, --force
Force immediate halt, power-off, reboot. Do not contact the init system.
-w, --wtmp-only
Only write wtmp shutdown entry, do not actually halt, power-off, reboot.
-d, --no-wtmp
Do not write wtmp shutdown entry.
--no-wall
Do not send wall message before halt, power-off, reboot.
EXIT STATUS
On success, 0 is returned, a non-zero failure code otherwise.
NOTES
These are legacy commands available for compatibility only.
SEE ALSO
systemd(1), systemctl(1), shutdown(8), wall(1)
systemd 208 HALT(8)