03-12-2016
Did you activate the new BE?
What's the output of the lustatus before reboot?
The new BE should be activated, from what I see it's not active on reboot.
7 More Discussions You Might Find Interesting
1. Solaris
Hello,
I started the upgrade using LiveUpgrade. I am using Solaris 10 instalation CDs (5 CDs). My server is Enterprise 3500 - SPARC.
1) lucreate -c first_disk -m /:/dev/dsk/c0t11d0s7:ufs -n second_disk
...
luupgrade -u -n second_disk -s /cdrom/cdrom0/s0
WARNING: <5> packages failed to... (0 Replies)
Discussion started by: zafyil
0 Replies
2. Solaris
My Solaris machine is not booting.It just stops at the point
Boot device: /pci@1e,600000/ide@d/disk@0,0:a File and args:
Whether i try boot or boot -s it is stopping at this point..
I tried boot cdom -s.It went into single user mode but I am not able to run a fsck in this mode.
Right... (1 Reply)
Discussion started by: lydiaEd
1 Replies
3. Solaris
I got this output from a system running solaris 10 :
# lustatus
BE_name Complete Active ActiveOnReboot CopyStatus
--------------------------------------------------------------------------------
oldvol yes yes yes -
newvol no no no -
bigvol no no no -
#
How do i remove (or... (1 Reply)
Discussion started by: ibroxy
1 Replies
4. Solaris
OK, latest in a loooong trail of errors with no information. I've finally gotten a new BE created on another drive, run liveupgrade on it to bring it from sol10u3 to sol10u8
I luactivate sol10u8
lustatus shows the sol10u8 as the active one
init 6
system just starts into 10u3 again.
I'm... (4 Replies)
Discussion started by: awoodby
4 Replies
5. UNIX for Dummies Questions & Answers
Folks;
I have a Solaris 9 server that after power outage it won't come fully up and i was able to bring it up in single user mode and checked "/var/log/messages" & "/var/adm/messages" with nothing showing since Sept. 17.
i ran fsck and no luck.
I ran all tests from the OK prompt with no luck... (2 Replies)
Discussion started by: Katkota
2 Replies
6. Solaris
What type of communication does Solaris 10/09 need to do with it's default gateway before it can boot up? (7 Replies)
Discussion started by: bstauffer
7 Replies
7. Solaris
Hi all,
I have got a few questions on the above topic ->
q1) if my intention for creating an ABE is just to use for patching / patchset update -
e.g. ./installpatchset -B secondboot --s10patchset
luactivate secondboot
What is the recommendation that my ABE should consist of ?... (5 Replies)
Discussion started by: javanoob
5 Replies
LEARN ABOUT ULTRIX
reboot
reboot(8) System Manager's Manual reboot(8)
Name
reboot - automatic reboot procedures
Syntax
/etc/reboot [ -n ] [ -q ]
Description
The ULTRIX system is booted by loading a kernel image, usually into memory at location zero and transferring to zero. Because the system
is not reenterable, the kernel image must be read in from disk each time the system is bootstrapped.
When the reboot of a running system is desired, is normally used. If there are no users, can be used. The command causes the disks to be
synced, and then a multiuser reboot is initiated. The system is booted and an automatic disk check is performed. If the procedure suc-
ceeds, the system is then brought up for the users.
The system will reboot itself after a power failure or after a crash, provided auto-restart is enabled on your system. A consistency check
of the file systems will be performed and, unless the check fails, the system will resume multiuser operations.
Options
-n Prevents the disks from being synced.
-q Reboots quickly and ungracefully, without shutting down running processes first.
Files
System code
See Also
crash(8v), fsck(8), halt(8), init(8), newfs(8), rc(8), shutdown(8)
reboot(8)