Sponsored Content
Operating Systems AIX Shared-SMT-4 vs Dedicated-SMT-4 on capped LPAR Post 302967796 by amitlib on Sunday 28th of February 2016 10:14:24 AM
Old 02-28-2016
Shared-SMT-4 vs Dedicated-SMT-4 on capped LPAR

Hi,

I have a POWER8 server running in Processor Implementation Mode: POWER 7.
I have 2 LPAR's, both are capped with 4 cores.

One of them displays:
Code:
Shared-SMT-4

and the other:
Code:
Dedicated-SMT-4

What is the difference when running in capped mode?

Thanks

Last edited by Scrutinizer; 02-28-2016 at 02:36 PM.. Reason: Quote tags
 

10 More Discussions You Might Find Interesting

1. AIX

Smt

How do you turn SMT(symm multi threading).I think that is what it's called.:) TIA Mike (2 Replies)
Discussion started by: mcastill66
2 Replies

2. HP-UX

Anything like AIX's SMT?

I'm working on a system to monitor a wide-range of Unix platforms, and I'd like to know if HP-UX has anything similar to AIX's SMT (simultaneous multithreading)? If there a way to separate an HP-UX CPU into multiple logical partitions which can then act as multiple CPUs? Thanks in advance, Dave (0 Replies)
Discussion started by: DaveZeltserman
0 Replies

3. Programming

Shared memory for shared library

I am writing a shared library in Linux (but compatible with other UNIXes) and I want to allow multiple instances to share a piece of memory -- 1 byte is enough. What's the "best" way to do this? I want to optimize for speed and portability. Obviously, I'll have to worry about mutual exclusion. (0 Replies)
Discussion started by: otheus
0 Replies

4. AIX

Enable SMT

How to enable SMT in aix 5.2 ml 9? If i run smtctl it gives error ksh: smtctl: not found. please tell me if SMT is supported in 5.2 (4 Replies)
Discussion started by: vjm
4 Replies

5. Solaris

capped-memory in zone

How does capped-memory work in zones? I have 32G of memory and 10 zones. I want about physical=4G and swap=4G in each zone. Is this possible? I am going over the 32G. (1 Reply)
Discussion started by: photon
1 Replies

6. AIX

LPAR freezes after switching of storage (lpar is mirrored)

Hi all, I have the following configuration 2 ds3524 storage disk systems located over 2 locations 2 P720 server located over 2 locations DS3524 are connected to san switch. Each vio server has 1 fc adapter attached to a san switch. per p720 server 2 virtual io servers. Vio 1 has 1 lun... (2 Replies)
Discussion started by: markiemark
2 Replies

7. Solaris

zone breaching 'capped-memory' threshold

Calling upon all Solaris zone experts. I have a Sun T3-1 that is running a few whole-root zones. I've set the 'capped-memory' setting on all the zones. However, I have a problem on the one zone. Under load it uses more memory that has been allocated to it. zonecfg -z sunrep02 export ... (4 Replies)
Discussion started by: soliberus
4 Replies

8. Programming

Shared library with acces to shared memory.

Hello. I am new to this forum and I would like to ask for advice about low level POSIX programming. I have to implement a POSIX compliant C shared library. A file will have some variables and the shared library will have some functions which need those variables. There is one special... (5 Replies)
Discussion started by: iamjag
5 Replies

9. Solaris

Finding capped memory of a non global zone

Is there a way to find the capped memory of a solaris non global zone from the non global zone itself (given rcapd is disabled) (6 Replies)
Discussion started by: CuriousDev
6 Replies

10. AIX

How to differentiate between a standalone LPAR and a VIOC (which again is a lpar)?

There can be configurations in IBM Server wherein a standalone partition is created on some supported IBM Server Or A VIOS - VIOC LPARs created. Now in both cases they are lpars. But if I want to differentiate b/w a standalone LPAR vs an VIOC LPAR how can I do..? On a... (2 Replies)
Discussion started by: Manish00712
2 Replies
victor(1)																 victor(1)

NAME
victor - attempts to discharge verification conditions using SMT solvers SYNOPSIS
victor [UNIT] DESCRIPTION
The victor command is a wrapper around ViCToR (vct) which simplifies its use. ViCToR translates SPARK verification conditions into SMTlib and feeds them to an SMT solver. SPARK ships with one such SMT solver, alt-ergo, but it is possible to use others solvers such as cvc3. The intended use of victor is to discharge true VCs left over by the Simplifier and not replace the Simplifier. Please also note that ViC- ToR is considered to be an experimental feature at the moment. This manual page only summarises the victor command-line flags, please refer to the full VictorWrapper manual for further information. OPTIONS
These options do not quite follow the usual GNU command line syntax as options start with a single dash instead of the usual two. -h, -help Shows command-line help. -t=SECONDS Time-out the SMT solver after this many seconds (by default 5) using ulimit. To disable time-out specify 0. -m=MEGABYTES Limit the SMT solver to this many MiB of virtual memory (by default no limit) using ulimit. -v Ignore the presence of any siv files and process vcg files only. By default, given a UNIT such as foo, victor will first attempt to process foo.siv and then fall back to foo.vcg. -plain Plain mode -- supress timings and versions. -solver=SOLVER Specifies an alternative SMT solver. By default we use alt-ergo. Can be one of alt-ergo, cvc3, yices or z3. The alt-ergo solver is distributed with SPARK. The cvc3 solver is part of Debian. The yices and z3 solvers are proprietary. SEE ALSO
spark(1), sparksimp(1), spadesimp(1), zombiescope(1), pogs(1) sparkformat(1), sparkmake(1) cvc3(1) AUTHOR
This manual page was written by Florian Schanda <florian.schanda@altran-praxis.com> for the Debian GNU/Linux system (but may be used by others). Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Ver- sion 1.3 or any later version published by the Free Software Foundation; with no Invariant Sections, no Front-Cover Texts and no Back-Cover Texts. 22 March 2011 victor(1)
All times are GMT -4. The time now is 07:01 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy