I want to perform ssh tunnelling for which I have been using PuTTy. Config is as follows:
Host IP:
Port:
Tunnel setting source port:
Destination:
After entering my user ID and password, I am able to see in my command prompt that
is listening.
Now I want to use the ssh command for tunnelling.
This is what I have done so far:
Using PuTTy to connect to server:
Host IP:
Port:
After entering my user ID and password, I run the command:
It then asks for my password. After I provide it, I check the command prompt, but now there is no configuration
present in the "Listening" state.
Hello,
I am within a LAN system and I need to be able to tunnel out (and recv UDP) packets.
Currently the router automatically drops UDP packets.
My PC cant see the outside world, nor ping, but it can connect via SSH to a server on the "edge" of the network which can see everything. I... (2 Replies)
Hi,
I have tried the following:
on PC1 (win xp) I have created ssh connection with port forwarding
(local 8888 to remote 8888) to server1.
>From server1 I have created another ssh connection with port
forwarding to server2(local 8888 to remote 1521).
When I try to connect to oracle... (3 Replies)
Hi all
question -
there are 2 servers A + B. server A is connected to the internet and running a squid proxy server - server B is behind a firewall. I can ssh from A to B but not from B to A. I need internet access on B to update some files. I thought I could use some sort of ssh tunnel to... (1 Reply)
Hello Folks,
Im trying to pass the NFS Shared data through the SSH tunnel. Following are the Steps for my Executions:
A) Commands Executed on Server (NFS Server + SSHD Server running)
i) share -F nfs -o rw=<NFS Server IP> /home
ii) Start the NFS Server Services and SSHD Services.
... (3 Replies)
Hi - I frequently run commands, and transfer files to/from a host that uses SecurID ssh authentication. It is a real pain to have to enter the authentication information every time I want to interact with this host. I am wondering if there is a way to establish a one-time ssh connection to this... (2 Replies)
Performing UDP tunneling through an SSH connection
Found this while looking for a way to temporarily forward SNMP requests across otherwise disconnected networks. Might be useful for someone else, too. (1 Reply)
So this seems like something that should be simple...but I can't quite seem to get it up and running. I have a machine, .107 with a GUI on port 8443. The problem is that I can't connect directly to .107 from my laptop. Now I have another machine, .69 that can connect to .107. So shouldn't I be able... (4 Replies)
Is it secure to use free shells for ssh tunneling? Can the shell provider see and log the sites I visit and passwords I enter?
I'm new to this thing and couldn't find info on google :o (5 Replies)
Hi!
I came to know about SSH Tunneling to bypass the Firewall.
I will have to setup a free access SSH server to tunnel data access through PUTTY or OpenSSH.
The problem is that I don't know about any free access servers.
So, can anyone of you guide me for that, for any type of help? (1 Reply)
I have a process running on my local server.
http://dev.techx.com:6060/proct
I wish to block port 6060 and expose port 7777 to the outside world.
I block port 6060 and open port 7777 on the firewall.
What should be the PuTTY Settings -> Connection -> SSH -> Tunnels
1. Destination ... (3 Replies)
Discussion started by: mohtashims
3 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)