We have a Unix system with two hard drives. When we tried to access it this morning it had frozen, and when we rebooted it couldn't find one of the hard drives, and had quite a few bad data blocks on the other. Of course we fear the worst: that the drive is completely gone, but were not sure how... (1 Reply)
Our SUn Solaris Server has crashed second time in 2 days, reason is not known , we are trying to determine what could have gone wrong, any ideas, the power supply seems to be fine, there is no response from keyboard,monitor etc and we had to do a hot boot yesterday..
Any suggestions what could be... (9 Replies)
Hi,
First of all, thanks for your help. I have downloaded freeBSD to study unix
I'm here again 'cause my HP-UX 10.x has "broken". It raise this error:
----------------------------------------------------
Diagnostic System warning:
= 0x1f005000 is POWERFAILED The diagnostic logging... (1 Reply)
hi friends,
i know that when there is a crash then that memory image is
put into /var/adm/crash
but if the system hangs up and if i have access to console of
that machine then how can i take the crash dump manully.
thanks (2 Replies)
I installed solaris 5.9 on a machine SunBlade100 512Mo of RAM and 18Go of hard disc, after the installation I have remark that the machine starts again after 10mn with 15 mn of walk, I downloaded and installed the last patchs on the machine but the poblème persists. someone can help me and tell me... (0 Replies)
Hi, First post. I am not to experienced in the Unix or HP-UX world but I'm learning.
We have some problem with a HP rx4640 server. During boot it states the following:
Checking for LVM volume groups and Activating (if any exist)
Volume group "/dev/vg00" has been successfully changed.
vgchange:... (7 Replies)
I am supporting a server running Solaris 4.3.The server is not having ddicated system administrator and i am requred to do minor maintenance tasks.l From few days, The server is automatically crashing and i just reboot the server. I also do not see anything in /var/adm/messages that can give an... (1 Reply)
Hi,
I need help, one of our servers is down, and all data in that Server are critical:
The Scenario:
-------------
I have a computer with the next architecture:
architecture=IA32
bus_types=PCI2.10,ISA,PnP1.0
hostname=xxx.xxx.xxx (the real name is hidden)
hw_provider=Generic AT... (2 Replies)
Discussion started by: danilosevilla
2 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)