We have a Unix system with two hard drives. When we tried to access it this morning it had frozen, and when we rebooted it couldn't find one of the hard drives, and had quite a few bad data blocks on the other. Of course we fear the worst: that the drive is completely gone, but were not sure how... (1 Reply)
Our SUn Solaris Server has crashed second time in 2 days, reason is not known , we are trying to determine what could have gone wrong, any ideas, the power supply seems to be fine, there is no response from keyboard,monitor etc and we had to do a hot boot yesterday..
Any suggestions what could be... (9 Replies)
Hi,
First of all, thanks for your help. I have downloaded freeBSD to study unix
I'm here again 'cause my HP-UX 10.x has "broken". It raise this error:
----------------------------------------------------
Diagnostic System warning:
= 0x1f005000 is POWERFAILED The diagnostic logging... (1 Reply)
hi friends,
i know that when there is a crash then that memory image is
put into /var/adm/crash
but if the system hangs up and if i have access to console of
that machine then how can i take the crash dump manully.
thanks (2 Replies)
I installed solaris 5.9 on a machine SunBlade100 512Mo of RAM and 18Go of hard disc, after the installation I have remark that the machine starts again after 10mn with 15 mn of walk, I downloaded and installed the last patchs on the machine but the poblème persists. someone can help me and tell me... (0 Replies)
Hi, First post. I am not to experienced in the Unix or HP-UX world but I'm learning.
We have some problem with a HP rx4640 server. During boot it states the following:
Checking for LVM volume groups and Activating (if any exist)
Volume group "/dev/vg00" has been successfully changed.
vgchange:... (7 Replies)
I am supporting a server running Solaris 4.3.The server is not having ddicated system administrator and i am requred to do minor maintenance tasks.l From few days, The server is automatically crashing and i just reboot the server. I also do not see anything in /var/adm/messages that can give an... (1 Reply)
Hi,
I need help, one of our servers is down, and all data in that Server are critical:
The Scenario:
-------------
I have a computer with the next architecture:
architecture=IA32
bus_types=PCI2.10,ISA,PnP1.0
hostname=xxx.xxx.xxx (the real name is hidden)
hw_provider=Generic AT... (2 Replies)
Discussion started by: danilosevilla
2 Replies
LEARN ABOUT MOJAVE
locale::codes::langext
Locale::Codes::LangExt(3pm) Perl Programmers Reference Guide Locale::Codes::LangExt(3pm)NAME
Locale::Codes::LangExt - standard codes for language extension identification
SYNOPSIS
use Locale::Codes::LangExt;
$lext = code2langext('acm'); # $lext gets 'Mesopotamian Arabic'
$code = langext2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langext_codes();
@names = all_langext_names();
DESCRIPTION
The "Locale::Codes::LangExt" module provides access to standard codes used for identifying language extensions, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language extensions. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lext = code2langext('acm','alpha');
$lext = code2langext('acm',LOCALE_LANGEXT_ALPHA);
The codesets currently supported are:
alpha
This is the set of three-letter (lowercase) codes from the IANA language registry, such as 'acm' for Mesopotamian Arabic.
This is the default code set.
ROUTINES
code2langext ( CODE [,CODESET] )
langext2code ( NAME [,CODESET] )
langext_code2code ( CODE ,CODESET ,CODESET2 )
all_langext_codes ( [CODESET] )
all_langext_names ( [CODESET] )
Locale::Codes::LangExt::rename_langext ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangExt::add_langext ( CODE ,NAME [,CODESET] )
Locale::Codes::LangExt::delete_langext ( CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_alias ( NAME ,NEW_NAME )
Locale::Codes::LangExt::delete_langext_alias ( NAME )
Locale::Codes::LangExt::rename_langext_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::add_langext_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangExt::delete_langext_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2013 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.18.2 2013-11-04 Locale::Codes::LangExt(3pm)