02-04-2016
What's your OS, compiler, and compile/link command?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
We have a Unix system with two hard drives. When we tried to access it this morning it had frozen, and when we rebooted it couldn't find one of the hard drives, and had quite a few bad data blocks on the other. Of course we fear the worst: that the drive is completely gone, but were not sure how... (1 Reply)
Discussion started by: Kgatliffe
1 Replies
2. UNIX for Dummies Questions & Answers
Our SUn Solaris Server has crashed second time in 2 days, reason is not known , we are trying to determine what could have gone wrong, any ideas, the power supply seems to be fine, there is no response from keyboard,monitor etc and we had to do a hot boot yesterday..
Any suggestions what could be... (9 Replies)
Discussion started by: knarayan
9 Replies
3. HP-UX
Hi,
First of all, thanks for your help. I have downloaded freeBSD to study unix
I'm here again 'cause my HP-UX 10.x has "broken". It raise this error:
----------------------------------------------------
Diagnostic System warning:
= 0x1f005000 is POWERFAILED The diagnostic logging... (1 Reply)
Discussion started by: efrenba
1 Replies
4. HP-UX
hi friends,
i know that when there is a crash then that memory image is
put into /var/adm/crash
but if the system hangs up and if i have access to console of
that machine then how can i take the crash dump manully.
thanks (2 Replies)
Discussion started by: mxms755
2 Replies
5. Solaris
I installed solaris 5.9 on a machine SunBlade100 512Mo of RAM and 18Go of hard disc, after the installation I have remark that the machine starts again after 10mn with 15 mn of walk, I downloaded and installed the last patchs on the machine but the poblème persists. someone can help me and tell me... (0 Replies)
Discussion started by: toufik
0 Replies
6. Solaris
Can anyone of you help me in enabling crash dump on Solaris 5.5.1 (1 Reply)
Discussion started by: csreenivas
1 Replies
7. Filesystems, Disks and Memory
Hi, First post. I am not to experienced in the Unix or HP-UX world but I'm learning.
We have some problem with a HP rx4640 server. During boot it states the following:
Checking for LVM volume groups and Activating (if any exist)
Volume group "/dev/vg00" has been successfully changed.
vgchange:... (7 Replies)
Discussion started by: hoff
7 Replies
8. Solaris
hi ,
i have machine that is crashed
how i can enable core dump file & how can i find it ? :confused: (4 Replies)
Discussion started by: lid-j-one
4 Replies
9. Solaris
I am supporting a server running Solaris 4.3.The server is not having ddicated system administrator and i am requred to do minor maintenance tasks.l From few days, The server is automatically crashing and i just reboot the server. I also do not see anything in /var/adm/messages that can give an... (1 Reply)
Discussion started by: asalman.qazi
1 Replies
10. SCO
Hi,
I need help, one of our servers is down, and all data in that Server are critical:
The Scenario:
-------------
I have a computer with the next architecture:
architecture=IA32
bus_types=PCI2.10,ISA,PnP1.0
hostname=xxx.xxx.xxx (the real name is hidden)
hw_provider=Generic AT... (2 Replies)
Discussion started by: danilosevilla
2 Replies
crash(8v) crash(8v)
Name
crash - what happens when the system crashes
Description
This section explains what happens when the system crashes and shows how to analyze crash dumps.
When the system crashes voluntarily it prints a message on the console in the form:
panic: explanation
The system takes a dump on a mass storage peripheral device or the network, and then invokes an automatic reboot procedure as described in
Unless there is some unexpected inconsistency in the state of the file systems due to hardware or software failure, the system then resumes
multi-user operations. If auto-reboot is disabled, the system halts at this point.
The system has a large number of internal consistency checks; if one of these fails, it prints a short message indicating which one failed.
The most common cause of system failures is hardware failure. In all cases there is the possibility that hardware or software error pro-
duced the message in some unexpected way. These messages are the ones you are likely to encounter:
IO err in push
hard IO err in swap
The system encountered an error when trying to write to the paging device or an error in reading critical information from a disk
drive. Fix your disk if it is broken or unreliable.
timeout table overflow
Due to the current data structure, running out of entries causes a crash. If this happens, make the timeout table bigger.
Exception Condition
An unexpected system error has occurred. The exception types are as follows:
---------------------------------------------------------------
Mnemonic Description
---------------------------------------------------------------
INT External interrupt
MOD TLB modification exception
TLBL TLB miss exception (load or instruction fetch)
TLBS TLB miss exception (store)
AdEL Address error exception (load or instruction fetch)
AdES Address error exception (store)
IBE Bus error exception (for an instruction fetch)
DBE Bus error exception (for a data load or store)
Sys Sys call exception
Bp Breakpoint exception
CpU Coprocessor unusable exception
Ovf Arithmetic overflow exception
---------------------------------------------------------------
KSP not valid
This indicates either a problem in the system or failing hardware.
init died
The system initialization process has exited. The only solution is the automatic reboot procedure described in Until this is done,
new users cannot log in.
When the system crashes, it attempts to write an image of memory into the back end of the primary swap area. After the system is rebooted,
the program runs and preserves a copy of this core image and the current system in a specified directory for later access. See for
details.
To analyze a dump, you should begin by running with the flag on the core dump.
See Also
dbx(1), reboot(8), savecore(8)
RISC crash(8v)