Hi I'm new to this forum and I'm a beginner when it comes to shell and awk programming. But I have the following problem:
I have 5 csv files (data1.csv, data2.csv, etc.) and need to calculate the average between the total sum of the 1st and 7 column.
csv example:... (3 Replies)
I have some data that is something like this?
item: onhand counted location
ITEM0001 1 0 a1
ITEM0001 0 1 a2
ITEM0002 5 0 b5
ITEM0002 0 6 c1
I want to sum up... (6 Replies)
can anyone help me how do i add the colums using awk seperated by character @. for eg i have
3@4
2@9
5@1
the result should be
10 14
i tried using
{ sum+= $1 }
END { print sum }
but it just gives the result 10. can anyone help me with this one
thank you and best regards (7 Replies)
Hello there.
I want some help with awk
I have this script that reads a file from awk and you can insert from keyboard any list from the fields that exist so to be printed on monitor
echo "give a choice"
read -a ans
array=${ans}
awk -F: -v k="$array" '{
... (4 Replies)
Hi,
I am unable sum of each column in the loop usng awk command.
Awk is not allowing the parameters in the command.
i am facing the below error.
awk: 0602-562 Field $() is not correct.
Source file
abc.txt
100,200,300,400,500,600,700,800,900
101,201,301,401,501,601,701,801,901
... (1 Reply)
// AIX 5.3 & AIX 6.1
ls -al |awk '{print $5}'
This gives each file's size in byte.
I need to get:
- the sum of all files in Giga bytes with loop.
- excluding the size of directories (ls -al returns the size of directories).
There are hundreds and thousands of files, so summing up... (8 Replies)
Hi Friends..
I'm completely new to Unix and I need to write a program / script to sum amount columns in a .DAT file by using a configuration file to read the position of the columns. Could someone pls. help me on how to proceed?
I've never written a program to read a configuration file and... (3 Replies)
Hi,
I have an awk command that I am using, and part of it sums COL_9 however when I read the output it is not including decimal places;
awk '
BEGIN{FS=OFS=","}
NR==1{print;next}
{a+=$9
c = $12
d = $18
}
END{for(i in a) {split(i,b,";"); print $1, $2, $3, b, $5, $6, b, b, a, $10, $11,... (1 Reply)
Hello everyone
I am a beginner in Shell scripting. Need your help to achieve desired result.
I have a file (sample format below)
001g8aX0007jxLz xxxxxxxxxxxxxxx 9213974926411 CO-COMM-133 CO-L001-DLY 7769995578239 44938 1 1
... (1 Reply)
Discussion started by: Rohit Mallah
1 Replies
LEARN ABOUT PHP
total
TOTAL(1) General Commands Manual TOTAL(1)NAME
total - sum up columns
SYNOPSIS
total [ -m ][ -sE | -p | -u | -l ][ -i{f|d}[N] ][ -o{f|d} ][ -tC ][ -N [ -r ]] [ file .. ]
DESCRIPTION
Total sums up columns of real numbers from one or more files and prints out the result on its standard output.
By default, total computes the straigt sum of each input column, but multiplication can be specified instead with the -p option. Likewise,
the -u option means find the upper limit (maximum), and -l means find the lower limit (minimum).
Sums of powers can be computed by giving an exponent with the -s option. (Note that there is no space between the -s and the exponent.)
This exponent can be any real number, positive or negative. The absolute value of the input is always taken before the power is computed
in order to avoid complex results. Thus, -s1 will produce a sum of absolute values. The default power (zero) is interpreted as a straight
sum without taking absolute values.
The -m option can be used to compute the mean rather than the total. For sums, the arithmetic mean is computed. For products, the geomet-
ric mean is computed. (A logarithmic sum of absolute values is used to avoid overflow, and zero values are silently ignored.)
If the input data is binary, the -id or -if option may be given for 64-bit double or 32-bit float values, respectively. Either option may
be followed immediately by an optional count, which defaults to 1, indicating the number of double or float binary values to read per
record on the input file. (There can be no space between the option and this count.) Similarly, the -od and -of options specify binary
double or float output, respectively. These options do not need a count, as this will be determined by the number of input channels.
A count can be given as the number of lines to read before computing a result. Normally, total reads each file to its end before producing
its result, but this behavior may be overridden by inserting blank lines in the input. For each blank input line, total produces a result
as if the end-of-file had been reached. If two blank lines immediately follow each other, total closes the file and proceeds to the next
one (after reporting the result). The -N option (where N is a decimal integer) tells total to produce a result and reset the calculation
after every N input lines. In addition, the -r option can be specified to override reinitialization and thus give a running total every N
lines (or every blank line). If the end of file is reached, the current total is printed and the calculation is reset before the next file
(with or without the -r option).
The -tC option can be used to specify the input and output tab character. The default tab character is TAB.
If no files are given, the standard input is read.
EXAMPLE
To compute the RMS value of colon-separated columns in a file:
total -t: -m -s2 input
To produce a running product of values from a file:
total -p -1 -r input
BUGS
If the input files have varying numbers of columns, mean values will certainly be off. Total will ignore missing column entries if the tab
separator is a non-white character, but cannot tell where a missing column should have been if the tab character is white.
AUTHOR
Greg Ward
SEE ALSO cnt(1), neaten(1), rcalc(1), rlam(1), tabfunc(1)RADIANCE 2/3/95 TOTAL(1)