12-22-2015
What release of HPUX v3 are you using ?
Looks like the server is supported to run HPUX v3.
Be sure to get the latest release to avoid possible problems.
Unfortunately, not much to see from screenshot...
Is there any current release on that machine, can you boot into HPUX ?
Regards
Peasant.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
I work in a production support environment. All our PROD machines SPARC machines and Solaris O/S. I want to know how to find out what the hard disk size, RAM size etc. of our PROD machines. Please let me know if there is any way to find out this (other than from system administrator).
... (2 Replies)
Discussion started by: ramaraju
2 Replies
2. UNIX for Dummies Questions & Answers
Hello folks, had a question.
I was trying to install sudotool on HP -UX 11i.
I downloaded gzip file from sudo site and unzipped to /tmp folder on HP box
how do i install it??
do i need to run "swinstall" menu and then choose from there?
THanks!
karthik (1 Reply)
Discussion started by: karthikosu
1 Replies
3. HP-UX
Hi Experts
I have a C3000 workstation onto which I am trying to install 11i however I am running into the following error.
ENTRY_INIT failed, status = -4: Unrecoverable hardware error
(followed by a hex dump)
I have re-tried many times and on one occasion successfully got through to CD... (4 Replies)
Discussion started by: C3000
4 Replies
4. Solaris
I am trying to load Xwindows on a sun240 that was deployed without it. I have the Solaris 10 disk mounted and ready but I want to make sure that I can load a Xwindows using the pkgadd command. I know its a dumb question but I rather ask a dumb question vs scrogging the box (0 Replies)
Discussion started by: razor3928
0 Replies
5. Filesystems, Disks and Memory
I have an application which is running under AIX, HP UNIX, SCO, and LINUX(redhat and SuSE). and its dealing with some bulk amount of file handling, and some of my boxes are not very good in terms of resources like memory and disk space. so i wanted to know the statistics of each of my boxes. Like... (2 Replies)
Discussion started by: renjithram
2 Replies
6. Solaris
Installing Solaris 8 for the first time...on a SunBlade 100. I have original Solaris 8 CD's.
About 45 minutes into the installation, the install halts with the following errors:
ERROR: Could not open file /a/etc/vfstab
ERROR: Could not create the file system mount table /etc/vfstab
I... (4 Replies)
Discussion started by: cdunavent
4 Replies
7. AIX
Hi All,
I was trying to know more about RAM disk concept in AIX. I found something on IBM site.
I was able to create and use/delete RAM disk as per IBM instructions.
But as you guys know, this RAM disk is a temporary storage. (*when ever we reboot the AIX LPAR, content/RAM disk will be... (4 Replies)
Discussion started by: System Admin 77
4 Replies
8. HP-UX
After install product BB068AA vpars and integrity vm
hpux use 10gb(!!!) of ram.
swapinfo -tm
Mb Mb Mb PCT START/ Mb
TYPE AVAIL USED FREE USED LIMIT RESERVE PRI NAME
dev 8192 0 8192 0% 0 - 1 /dev/vg00/lvol2... (2 Replies)
Discussion started by: Linusolaradm1
2 Replies
9. HP-UX
Hi, I have a HP UX C8000 box , have installed 11.11i from 4 x cds numerous times to try to get a functioning Network or to try and get rid of this error on start up, after new install and 1st startup I get an error
"The desktop messaging system could not be started" and then advice about... (12 Replies)
Discussion started by: C8000
12 Replies
LEARN ABOUT DEBIAN
pull-lp-source
PULL-LP-SOURCE(1) General Commands Manual PULL-LP-SOURCE(1)
NAME
pull-lp-source - download a source package from Launchpad
SYNOPSIS
pull-lp-source [options] source package [release|version]
DESCRIPTION
pull-lp-source downloads and extracts the specified version of <source package> from Launchpad, or the latest version of the specified
release. To request a version from a particular pocket say release-pocket (with a magic -release for only the release pocket). If no ver-
sion or release is specified, the latest version in the development release will be downloaded.
OPTIONS
Listed below are the command line options for pull-lp-source:
source package
This is the source package that you would like to be downloaded from Launchpad.
version
This is the version of the source package to be downloaded.
release
This is the release that you would like the source package to be downloaded from. This value defaults to the current development
release.
-h, --help
Display a help message and exit.
-d, --download-only
Do not extract the source package.
-m UBUNTU_MIRROR, --mirror=UBUNTU_MIRROR
Use the specified Ubuntu mirror. Should be in the form http://archive.ubuntu.com/ubuntu. If the package isn't found on this mir-
ror, pull-lp-source will fall back to Launchpad, as its name implies.
--no-conf
Do not read any configuration files, or configuration from environment variables.
ENVIRONMENT
All of the CONFIGURATION VARIABLES below are also supported as environment variables. Variables in the environment take precedence to
those in configuration files.
DIST Specifies the default target.
CONFIGURATION VARIABLES
The following variables can be set in the environment or in ubuntu-dev-tools(5) configuration files. In each case, the script-specific
variable takes precedence over the package-wide variable.
PULL_LP_SOURCE_UBUNTU_MIRROR, UBUNTUTOOLS_UBUNTU_MIRROR
The default value for --mirror.
SEE ALSO
dget(1), pull-debian-source(1), pull-debian-debdiff(1), ubuntu-dev-tools(5)
AUTHOR
pull-lp-source and this manual page were written by Iain Lane <iain@orangesquash.org.uk>. Both are released under the GNU General Public
License, version 3 or later.
ubuntu-dev-tools 4 August 2008 PULL-LP-SOURCE(1)