How to modify the file mentioned in the Message details ?
i have a below file
the entire content in the fileis obtained by making two seperate Curl calls( one curl call gives me state when i grep the curl call with state and another curl call will give me Rno when i grep with Rno).
Now MY Question is i want the file in the below format .
How can i get it in this format ?
And also after getting the file in this format my next action would be
depending upon the value of state ( it might me CONNECTED or disconnected ) i would like to fetch the corresponding Rno .
Moderator's Comments:
edit by bakunin: When we asked you to use CODE-tagswe really meant it. This is not optional!
Hi Experts,
Im a new bee for scripting,
I would ned to do the following via linux shell scripting, I have an application which throws a log file, on each action of a particular work with the application, as sson as the action is done, the log file would vanish or stops updating there, the... (2 Replies)
#!/bin/sh
##########################################################################################################
#This script is being used for AOK application for cleaning up the .out files and zip it under logs directory.
# IBM
# Created
#For pdocap201/pdoca202 .out files for AOK
#1.... (3 Replies)
I have scheduled couple of shell scripts to run using 'at' command.
The o/p of at -l is:
$ at -l
1320904800.a Thu Nov 10 01:00:00 2011
1320894000.a Wed Nov 9 22:00:00 2011
1320876000.a Wed Nov 9 17:00:00 2011
$ uname -a
SunOS dc2prcrptetl2 5.9 Generic_122300-54 sun4u sparc... (2 Replies)
hello,
I have problem with writing/adjusting a shell script.
I searched forum and unfortunately couldn't write scipt based on the information I found.
I never wtire such so it's hard for me and I do need to modify one script immediately.
case looks like:
1. 'file' that needs to be modified... (3 Replies)
Hi,
I am trying to write a script with goes through thousands of XML documents to pull out the values for a particular tag to a .txt file.
For example I have
file1.xml
file2.xml
file3.xml
.
.
.
fileN.xml
All these files have a tag called <systemID>.
The value that sits within... (6 Replies)
Hi,
I need the details of which ids belong to the sudoers file, and which groups these ids belong to.
Can anyone suggest a way to derive that information into a flat file please?
G (4 Replies)
Hello experts, I want to join a file with files whosE names are mentioned in one of the columns of the same file.
File 1
t1,a,b,file number 1
t1,a,c,file number 1
t2,c,d,file number 2
t2,c,e,file number 2
t2,c,f,file number 2
t2,c,g,file number 2
t3,e,f,file number 3
file number 1... (3 Replies)
Hi
I have two text files. The first file is TEXTFILEONE.txt as given below:
<Text Text_ID="10155645315851111_10155645333076543" From="460350337461111" Created="2011-03-16T17:05:37+0000" use_count="123">This is the first text</Text>
<Text Text_ID="10155645315851111_10155645317023456"... (7 Replies)
ENUM WIMAX_ST(9) Linux Networking ENUM WIMAX_ST(9)NAME
enum_wimax_st - The different states of a WiMAX device
SYNOPSIS
enum wimax_st {
__WIMAX_ST_NULL,
WIMAX_ST_DOWN,
__WIMAX_ST_QUIESCING,
WIMAX_ST_UNINITIALIZED,
WIMAX_ST_RADIO_OFF,
WIMAX_ST_READY,
WIMAX_ST_SCANNING,
WIMAX_ST_CONNECTING,
WIMAX_ST_CONNECTED,
__WIMAX_ST_INVALID
};
CONSTANTS
__WIMAX_ST_NULL
The device structure has been allocated and zeroed, but still wimax_dev_add hasn't been called. There is no state.
WIMAX_ST_DOWN
The device has been registered with the WiMAX and networking stacks, but it is not initialized (normally that is done with 'ifconfig
DEV up' [or equivalent], which can upload firmware and enable communications with the device). In this state, the device is powered
down and using as less power as possible. This state is the default after a call to wimax_dev_add. It is ok to have drivers move
directly to WIMAX_ST_UNINITIALIZED or WIMAX_ST_RADIO_OFF in _probe after the call to wimax_dev_add. It is recommended that the driver
leaves this state when calling 'ifconfig DEV up' and enters it back on 'ifconfig DEV down'.
__WIMAX_ST_QUIESCING
The device is being torn down, so no API operations are allowed to proceed except the ones needed to complete the device clean up
process.
WIMAX_ST_UNINITIALIZED
[optional] Communication with the device is setup, but the device still requires some configuration before being operational. Some
WiMAX API calls might work.
WIMAX_ST_RADIO_OFF
The device is fully up; radio is off (wether by hardware or software switches). It is recommended to always leave the device in this
state after initialization.
WIMAX_ST_READY
The device is fully up and radio is on.
WIMAX_ST_SCANNING
[optional] The device has been instructed to scan. In this state, the device cannot be actively connected to a network.
WIMAX_ST_CONNECTING
The device is connecting to a network. This state exists because in some devices, the connect process can include a number of
negotiations between user space, kernel space and the device. User space needs to know what the device is doing. If the connect
sequence in a device is atomic and fast, the device can transition directly to CONNECTED
WIMAX_ST_CONNECTED
The device is connected to a network.
__WIMAX_ST_INVALID
This is an invalid state used to mark the maximum numeric value of states.
DESCRIPTION
Transitions from one state to another one are atomic and can only be caused in kernel space with wimax_state_change. To read the state, use
wimax_state_get.
States starting with __ are internal and shall not be used or referred to by drivers or userspace. They look ugly, but that's the point --
if any use is made non-internal to the stack, it is easier to catch on review.
All API operations [with well defined exceptions] will take the device mutex before starting and then check the state. If the state is
__WIMAX_ST_NULL, WIMAX_ST_DOWN, WIMAX_ST_UNINITIALIZED or __WIMAX_ST_QUIESCING, it will drop the lock and quit with -EINVAL, -ENOMEDIUM,
-ENOTCONN or -ESHUTDOWN.
The order of the definitions is important, so we can do numerical comparisons (eg: < WIMAX_ST_RADIO_OFF means the device is not ready to
operate).
COPYRIGHT Kernel Hackers Manual 2.6. July 2010 ENUM WIMAX_ST(9)